Abstract:This paper proposes a bulk micromachined bandpass filter on 0.5mm-thick Pyrex glass, whose operation is based on the splitting of the odd and even degenerate mode in a dual-mode resonator, with the addition of a perturbation element. In such a way, a filter may require only half resonators of a traditional one, resulting in a more compact configuration over those ever reported. A 4%-bandwidth bandpass filter centered at 17GHz was designed. The square-ring-like coplanar waveguide (CPW) act as a dual-mode resonator, and an open-circuited stub attached to the inner corner of the square-ring acts as the perturbation element and dominates the filter bandwidth. The two bulk-micromachined switches for tuning are placed symmetrically along the diagonal line. Since the electrical length of CPW is extended after being loaded by capacitive switches, both the degenerate resonating frequencies and the filter mid-band frequency are shifted downward. Theoretical formulas are derived for various actuation states of all the switches. The filter performance is analysed also using finite-element fullwave tools. A frequency shift of 0.6GHz is seen which is close to 0.58GHz obtained from analytical solutions. Both the original and tuned state come with satisfying microwave performance, i.e. low passband insertion-loss (< 0.5dB) and return-loss (< −15dB) and high stopband rejection. It is also shown that the simulated result is in good agreement with theoretical solutions. The bulk microfabrication is shown to be much simpler than surface micromachining conventionally used for RF MEMS switches. Since the bridge skeleton is Si, thermal mismatch between all-metal bridge and dielectric substrate is avoided, and reliability at elevated temperature is guaranteed or at least greatly improved. Besides, the p++ doped Si line patterned simultaneously with the microbridges, can also be used as a DC biasing resistor, which can eliminate the additional steps to fabricate the resistive alloy line. The tested results of the fabricated switch samples are also shown. The device may be a good candidate for novel Ku-band inter-scientific satellite communication or wireless networking.

A 12–16 GHz microelectromechanical system-switchable bandpass filter

3D Heterogenous Integrated Wideband Switchable Bandpass Filter Bank for Millimeter Wave Applications

Miniaturized Dual-Band Substrate Integrated Waveguide Filter with Controllable Bandwidths

Design of a Miniaturized Dual-Band Double-Folded Substrate Integrated Waveguide Bandpass Filter with Controllable Bandwidths

Novel microstrip bandpass filter with multiple transmission zeros and wide stopband

Substrate-Integrated Waveguide Bandpass Filters with Planar Resonators for System-on-Package

A Novel 76 and 94ghz Dual Band Bandpass Filter Using Multilayer Step Impedance Resonators (Sirs)

A CMOS 1.3-1.7GHz Q-Enhanced LC Band-pass RF Filter with 1.5-67% Tunable Fractional Bandwidth

Extended Doublet Bandpass Filters Implemented with Microstrip Resonator and Full-/Half-Mode Substrate Integrated Cavities

A Bulk Micromachined Tunable Dual-Mode Microwave Bandpass Filter on Coplanar Waveguide

Design Of Ku-Band Sir Interdigital Bandpass Filter Using Silicon-Based Micromachining Technology

Design and simulation of tunable bandstop filters by integrating RF MEMS shunt switch for K-band applications

Design and Fabrication of a MEMS Bandpass Filter with Different Center Frequency of 8.5-12 GHz.

Design of high selectivity tunable bandpass filter with switchable single‐/dual‐band responses

A Triple Channel High Rejection Rf Mems Switched Filter Bank

Switchable and Broadband Silicon Integrated Microwave Photonic Filter

A 10&#x2013;14 GHz RF MEMS Tunable Bandpass Filter

UHF Band Switchable Superconducting Filter with Pin Diode Switches

Design of compact dual-band switchable bandpass filter

An Ultra-Broadband Contact-Capacitive RF MEMS Switch for 15-110GHZ Applications

A Compact Bandpass Filter with Active Switchable Passband Status