Abstract:This paper proposes a bulk micromachined bandpass filter on 0.5mm-thick Pyrex glass, whose operation is based on the splitting of the odd and even degenerate mode in a dual-mode resonator, with the addition of a perturbation element. In such a way, a filter may require only half resonators of a traditional one, resulting in a more compact configuration over those ever reported. A 4%-bandwidth bandpass filter centered at 17GHz was designed. The square-ring-like coplanar waveguide (CPW) act as a dual-mode resonator, and an open-circuited stub attached to the inner corner of the square-ring acts as the perturbation element and dominates the filter bandwidth. The two bulk-micromachined switches for tuning are placed symmetrically along the diagonal line. Since the electrical length of CPW is extended after being loaded by capacitive switches, both the degenerate resonating frequencies and the filter mid-band frequency are shifted downward. Theoretical formulas are derived for various actuation states of all the switches. The filter performance is analysed also using finite-element fullwave tools. A frequency shift of 0.6GHz is seen which is close to 0.58GHz obtained from analytical solutions. Both the original and tuned state come with satisfying microwave performance, i.e. low passband insertion-loss (< 0.5dB) and return-loss (< −15dB) and high stopband rejection. It is also shown that the simulated result is in good agreement with theoretical solutions. The bulk microfabrication is shown to be much simpler than surface micromachining conventionally used for RF MEMS switches. Since the bridge skeleton is Si, thermal mismatch between all-metal bridge and dielectric substrate is avoided, and reliability at elevated temperature is guaranteed or at least greatly improved. Besides, the p++ doped Si line patterned simultaneously with the microbridges, can also be used as a DC biasing resistor, which can eliminate the additional steps to fabricate the resistive alloy line. The tested results of the fabricated switch samples are also shown. The device may be a good candidate for novel Ku-band inter-scientific satellite communication or wireless networking.

A Triple Channel High Rejection Rf Mems Switched Filter Bank

3D Heterogenous Integrated Wideband Switchable Bandpass Filter Bank for Millimeter Wave Applications

Selectable-FSR 10-Ghz Granularity WDM Superchannel Filter in a Reconfigurable Photonic Integrated Circuit

A 12–16 GHz microelectromechanical system-switchable bandpass filter

A Novel 76 and 94ghz Dual Band Bandpass Filter Using Multilayer Step Impedance Resonators (Sirs)

A triple-mode ring dielectric resonator band-pass filter using substrate integrated waveguide (SIW)

Design of Broadband High-Frequency Multi-Throw RF-MEMS Switches

A CMOS 1.3-1.7GHz Q-Enhanced LC Band-pass RF Filter with 1.5-67% Tunable Fractional Bandwidth

Design and Fabrication of a MEMS Bandpass Filter with Different Center Frequency of 8.5-12 GHz.

Design and simulation of tunable bandstop filters by integrating RF MEMS shunt switch for K-band applications

A Rf-Mems Based Dual-Band Tunable Filter with Independently Controllable Passbands

A High Isolation Series-Shunt Rf Mems Switch

High-Selective Bandpass Filters Based on New Dual-Mode Rectangular Strip Patch Resonators

A Bulk Micromachined Tunable Dual-Mode Microwave Bandpass Filter on Coplanar Waveguide

UHF Band Switchable Superconducting Filter with Pin Diode Switches

An Ultra-Broadband Contact-Capacitive RF MEMS Switch for 15-110GHZ Applications

A 10&#x2013;14 GHz RF MEMS Tunable Bandpass Filter

Compact Switchable Filter with Three State Modes Using Simple Microstrip Structure

Switchable Frequency Selective Surfaces Absorber/reflector for Wideband Applications

Design of a Switchable Filter for Reflectionless-Bandpass-to-Reflectionless-Bandstop Responses

A High-Performance, Low-Cost, and Integrated Hairpin Topology RF Switched Filter Bank for Radar Applications