Abstract:The effects of different modeling and solving approaches on the simulation of a steam ejector have been investigated with the computational fluid dynamics (CFD) technique. The four most frequently used and recommended turbulence models (standard k-ε, RNG k-ε, realizable k-ε and SST k-ω), two near-wall treatments (standard wall function and enhanced wall treatment), two solvers (pressure- and density-based solvers) and two spatial discretization schemes ( the second-order upwind scheme and the quadratic upstream interpolation for convective kinematics (QUICK) of the convection term have been tested and compared for a supersonic steam ejector under the same conditions as experimental data. In total, more than 185 cases of 17 different modeling and solving approaches have been carried out in this work. The simulation results from the pressure-based solver (PBS) are slightly closer to the experimental data than those from the density-based solver (DBS) and are thus utilized in the subsequent simulations. When a high-density mesh with y+ < 1 is used, the SST k-ω model can obtain the best predictions of the maximum entrainment ratio (ER) and an adequate prediction of the critical back pressure (CBP), while the realizable k-ε model with the enhanced wall treatment can obtain the best prediction of the CBP and an adequate prediction of the ER. When the standard wall function is used with the three k-ε models, the realizable k-ε model can obtain the best predictions of the maximum ER, and the three k-ε models can gain the same CBP value. For a steam ejector with recirculation inside the diffuser, the realizable k-ε model or the enhanced wall treatment is recommended for adoption in the modeling approach. When the spatial discretization scheme of the convection term changes from a second-order upwind scheme to a QUICK scheme, the effect can be ignored for the maximum ER calculation, while only the CBP value from the standard k-ε model with the standard wall function is reduced by 2.13%. The calculation deviation of the ER between the two schemes increases with the back pressure at the unchoked flow region, especially when the standard k-ε model is adopted. The realizable k-ε model with the two wall treatments and the SST k-ω model is recommended, while the standard k-ε is more sensitive to the near-wall treatment and the spatial discretization scheme and is not recommended for an ejector simulation.

Key Parameter Prediction and Validation for a Pilot-Scale Rotating-Disk Contactor by CFD–PBM Simulation

CFD-PBM Investigation on Droplet Size Distribution in a Liquid–Liquid Stirred Tank: Effect of Impeller Type

Progress on agitated apparatus for polymer devolatilization and its CFD simulation

Numerical Investigation of Hydrodynamics and Heat Transfer for Bingham-pseudoplastic Fluids in an Industrial Coiled Stirred Tank

Operating Regimes and Hydrodynamics of a Rotating‐Disc Contactor

A Pseudo-3D Model with 3D Accuracy and 2D Cost for the CFD–PBM Simulation of a Pilot-Scale Rotating Disc Contactor

Augmented CFD–PBM Simulation of Liquid–Liquid Two-Phase Flows in Liquid Extraction Columns with Wettable Internal Plates

An Improved Computational Fluid Dynamics-Discrete Bubble Model for Multiphase Bubble Flow Simulation with a Wide Grid/bubble Size Ratio

Effect of Suction and Discharge Conditions on the Unsteady Flow Phenomena of Axial-Flow Reactor Coolant Pump

3D-CFD Simulation of Liquid–Liquid Two-Phase Flow in A Pilot-Plant Scale Annular Pulsed Disc and Doughnut Column

CFD–PBM Simulation of Liquid–Liquid Dispersions in a Pump-Mixer

CFD Simulation of Holdup in Rotating Disc Contactor

An Improved Dynamic Combined Model for Evaluating the Mass Transfer Performances in Extraction Columns

CFD Simulation of Two-Phase Flow in a Hybrid Pulsed Sieve-Plate Solvent Extraction Column: Prediction of Holdup and Axial-dispersion Coefficients

Physical Modelling and Numerical Simulation of Velocity Fields in Rotating Disc Contactor Via Cfd Simulation and Ldv Measurement

Predicting cold gas-solid flow in a pilot-scale dual-circulating fluidized bed: Validation of computational particle fluid dynamics model

Assessment of Different CFD Modeling and Solving Approaches for a Supersonic Steam Ejector Simulation

CFD Simulation of Liquid–Liquid Two-Phase Hydrodynamics and Axial Dispersion Analysis for a Non-Pulsed Disc and Doughnut Solvent Extraction Column

Coupling of CFD with PBM for a pilot-plant tubular loop polymerization reactor

A Dynamic Forward Mixing Model for Evaluating the Mass Transfer Performances of an Extraction Column

Comprehensive Assessment of the Accuracy of CFD-DEM Simulations of Bubbling Fluidized Beds