Abstract:The development of ceramic-polymer composites is a focal point in the research of thermal protection systems, and the control of microstructure is crucial for fabricating high-performance resins. In order to investigate the effect of the silicon phase structure on the properties of epoxy resins and preparate the ablation-resistant ceramifiable resins, the homogeneous and "sea-island" phases of epoxy resins with different amounts of silicones were prepared by ring-opening and grafting reactions. The reaction mechanism and the microphase structure of silicone were verified by SEM and TEM. It was found that the homogeneous silicone-epoxy resins exhibited exceptional ablation resistance, with mass and linear ablation rates of 0.0646 g/s and 0.0073 mm/s, which were 78.61 % and 98.36 % lower than those of epoxy resins, and exceeded most of the resin-based ablation-resistant materials reported in the literatures. The homogeneous silicone further slows down the pyrolysis rate of the epoxy resin and inhibits the release of pyrolysis products. During the carbonization and ceramization, the carbothermal reduction reaction between silicon and carbon occurs sufficiently in the homogeneous system, which enhanced the content of SiC ceramics in the carbon layer. Eventually, a dense char layer with low porosity and a highly graphitized structure constructed in situ on the ablative surface, which greatly improves the ablative resistance. Furthermore, its exceptional mechanical properties render it capable of substituting conventional resin-based thermal protection materials, thereby meeting the stringent demands of challenging environments.

Modification of a Phenolic Resin with Epoxy- and Methacrylate-Functionalized Silica Sols to Improve the Ablation Resistance of Their Glass Fiber-Reinforced Composites

Preparation and Ablation Performance of Silica Modified Phenolic/carbon Fiber Composite

Improved Thermal Stabilities, Ablation and Mechanical Properties for Carbon Fibers/Phenolic Resins Laminated Composites Modified by Silicon-containing Polyborazine

Ablation experiments of silica phenolic resin material eroded by highly concentrated particles

Thermal protection materials based on epoxy‐containing and phenyl‐containing polyhedral oligomeric silsesquioxane modified phenolic resin and phenolic resin/carbon fiber composites

Promoted Ablation Resistance of Polydimethylsiloxane Via Crosslinking with Multi-Ethoxy POSS

Morphology Measurement on Phenolic-Resin/Vitreous-Silica-Fabric Ablation Composites Modified with Tetraethoxysilicate and Silsesquioxanes

Preparation and Characterization of Silica Fiber Reinforced Boron Modified Methyl Phenolic Resin Matrix Composites

Poly(dimethyl-diphenyl-imide)siloxane/phenolic-based double network hybrid resin coatings for ablation thermal protection

Improvement of Epoxy Resin with Glycidyl-Polyhedral Oligomeric Silsesquioxanes

Improving the ablation resistance of epoxy modified organosilicon resin synergistic modified with B2O3 and ZrSi2

B4C-MODIFIED SiO2-PHENOLIC COMPOSITES FOR ENHANCED ABLATION RESISTANCE

Research Progress in the Ablative Resistance of Modified Phenolic Resin

Oxidation and ablation behaviors of carbon fiber/phenolic resin composites modified with borosilicate glass and polycarbosilane interface

Ceramization of Coordinated Zr4+ and Hf4+ in Polysiloxane Conferring Silicone/phenolic Hybrid Resin with Excellent Thermal Protection

Improvement of Silicon and Epoxy Phase Interface by Constructing Rigid Interpenetrating Networks Based on Bismaleimide to Enhance Ablative, Mechanical and Thermal Properties

Enhancing ablation and oxidation resistance of phenolic resin with modified pickling asbestos

Effect of Mesophase Pitch Incorporation on the Ablation Behavior and Mechanism of Phenolic Composites

Preparation of Ceramifiable and Ablatively Resistant Epoxy Resins by Microphase Structure Modulation of Silicones

A Comparison of Ablative Resistance Properties of Liquid Silicone Rubber Composites Filled with Different Fibers

Preparation and Ablative Behaviors of Carbon Fiber‐reinforced Polydimethylsiloxane‐co‐poly(silylene Acetylenearyleneacetylene) Composites