Abstract:This paper presents an experimental investigation of the sample thickness effect on the concurrent flame steady spread behavior. Two configurations, ceiling flame and floor flame, as the fundamental diffusion combustion problems and representative scenarios of horizontal flame spread, are concerned herein. PMMA samples with thickness (delta) of 2, 3, 4, 5, 7, 9 mm were employed including both thermally-thin and thermally-thick conditions. A wind tunnel was used to provide the uniform concurrent airflow ranging from 0.3 m/s to 1.2 m/s in 0.3 m/s intervals. Flame characteristics and basic parameters to quantify the flame steady spread process have been studied, including flame spread rate (FSR), equivalent pyrolysis length as well as heat flux feedback in both pyrolysis and preheating zones. Results show that FSR decreases with sample thickness, being more sensitive to sample thickness for ceiling flame configuration than that for floor flame configuration. Equivalent pyrolysis length increases with sample thickness and ceiling flame's equivalent pyrolysis length is larger than floor flame's. Convection feedback is dominant under concurrent airflow regardless of the flame configuration, airflow velocity or sample thickness. In pyrolysis zone, the total heat flux to fuel surface of ceiling flame configuration is larger than that of floor flame configuration for thin samples due to buoyancy, but it decreases rapidly as sample thickness increases. In preheating zone, the heat flux decreases in power law for ceiling flame configuration while a piece-wise fitting is found for floor flame configuration, which is interpreted based on their inherent flame characteristic difference hence the thermal boundary layer conditions between these two configurations. To analyze the sample thickness effect on concurrent flame spread, a characteristic solid temperature (T*) is proposed by theoretical analysis, as an essential parameter to be used in the concurrent flame spread model to represent the coupling effect of heat input in gas phase and in-depth heat loss into the solid phase (or namely thermal inertia controlled by a characteristic thermal penetration depth). The calculated non-dimensional characteristic solid temperature (theta) shows to be less sensitive to flame configuration and concurrent airflow velocity for relatively thicker samples because the thermal penetration depth will tend to approach a limit. A general trend of its variation with sample thickness (delta) can be employed to predict the heat loss into solid phase and its predictive capability is verified by the experimental results. This work advances the fundamental understanding of the sample thickness effect on concurrent flame spread mechanism. (C) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Effect of finite dimension on downward flame spread over PMMA slabs: Experimental and theoretical study

Width Effects on Downward Flame Spread over Poly(methyl Methacrylate) Sheets

Experimental and theoretical study on downward flame spread over uninhibited PMMA slabs under different pressure environments

Sample Width and Thickness Effects on Upward Flame Spread over PMMA Surface.

Study on the influence of restricted distance on fixed-width discrete of discontinuous flame spread

Experimental Study of Upward Flame Spread Behaviors over Thermally Thick Vertical PMMA of Various Sample Widths under Normal Wind

Upward Flame Spread over an Array of Discrete Thermally-Thin PMMA Plates

Effect of Sample Thickness on Concurrent Steady Spread Behavior of Floor- and Ceiling Flames

Prediction of Three-Dimensional Downward Flame Spread Characteristics over Poly(methyl Methacrylate) Slabs in Different Pressure Environments

Effects of Sample Width on Downward Flame Spread over RPU Slabs

Experimental Study of Flame Spread over Thermally-Thin Inclined Fuel Surface and Controlling Heat Transfer Mechanism under Concurrent Wind

Effect of solid surface curvature and wall heat loss on the downward flame spread along the edge of thin PMMA sheets

Upward Flame Spread over Discrete Thick Fuels under Mixed Convection Flow

Experimental Study on Flame Spread over Inclined PMMA and PE Slabs

Influences of Low Atmospheric Pressure on Downward Flame Spread over Thick Pmma Slabs at Different Altitudes

Experimental study on the influence of restricted distance on the discrete flame spread of different widths

Effect of ceiling height on flame spread over horizontal poly(methyl methacrylate) slabs in corridor

Experimental study on influence of air gap on upward flame spread over discrete fuel

Experimental Study on Coupled Combustion of PMMA Counter-directional Flame Spread in the Horizontal Direction

Lateral Flame Spread over PMMA under Forced Air Flow

Effects of Ceiling Inclination on Lateral Flame Spread over Vertical Poly(methyl Methacrylate) Surface