Abstract:This paper presents an experimental investigation of the sample thickness effect on the concurrent flame steady spread behavior. Two configurations, ceiling flame and floor flame, as the fundamental diffusion combustion problems and representative scenarios of horizontal flame spread, are concerned herein. PMMA samples with thickness (delta) of 2, 3, 4, 5, 7, 9 mm were employed including both thermally-thin and thermally-thick conditions. A wind tunnel was used to provide the uniform concurrent airflow ranging from 0.3 m/s to 1.2 m/s in 0.3 m/s intervals. Flame characteristics and basic parameters to quantify the flame steady spread process have been studied, including flame spread rate (FSR), equivalent pyrolysis length as well as heat flux feedback in both pyrolysis and preheating zones. Results show that FSR decreases with sample thickness, being more sensitive to sample thickness for ceiling flame configuration than that for floor flame configuration. Equivalent pyrolysis length increases with sample thickness and ceiling flame's equivalent pyrolysis length is larger than floor flame's. Convection feedback is dominant under concurrent airflow regardless of the flame configuration, airflow velocity or sample thickness. In pyrolysis zone, the total heat flux to fuel surface of ceiling flame configuration is larger than that of floor flame configuration for thin samples due to buoyancy, but it decreases rapidly as sample thickness increases. In preheating zone, the heat flux decreases in power law for ceiling flame configuration while a piece-wise fitting is found for floor flame configuration, which is interpreted based on their inherent flame characteristic difference hence the thermal boundary layer conditions between these two configurations. To analyze the sample thickness effect on concurrent flame spread, a characteristic solid temperature (T*) is proposed by theoretical analysis, as an essential parameter to be used in the concurrent flame spread model to represent the coupling effect of heat input in gas phase and in-depth heat loss into the solid phase (or namely thermal inertia controlled by a characteristic thermal penetration depth). The calculated non-dimensional characteristic solid temperature (theta) shows to be less sensitive to flame configuration and concurrent airflow velocity for relatively thicker samples because the thermal penetration depth will tend to approach a limit. A general trend of its variation with sample thickness (delta) can be employed to predict the heat loss into solid phase and its predictive capability is verified by the experimental results. This work advances the fundamental understanding of the sample thickness effect on concurrent flame spread mechanism. (C) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Effect of ceiling height on flame spread over horizontal poly(methyl methacrylate) slabs in corridor

Flame behavior and fire-induced flow field characteristic in building corridor fire with longitudinal partition

Study on the influence of restricted distance on fixed-width discrete of discontinuous flame spread

Heat flux and flame spread rate of discrete PMMA in concave building facade with window intervals

Experimental Study on Coupled Combustion of PMMA Counter-directional Flame Spread in the Horizontal Direction

Experimental investigation on transverse ceiling flame length and temperature distribution of sidewall confined tunnel fire

Effect of Sample Thickness on Concurrent Steady Spread Behavior of Floor- and Ceiling Flames

Experimental study of flame extension behavior under different curved ceilings in underground spaces

Impinging Ceiling Flame Behaviors Induced by Wall-Attached Gaseous Fuel Fires at One End in a Narrow Building Corridor: Different Phases and Generalized Correlations

Experimental study on the influence of restricted distance on the discrete flame spread of different widths

Effects of Overlap Length on Flammability and Fire Hazard of Vertical Polymethyl Methacrylate (PMMA) Plate Array

Experimental Study on Behavior of Sidewall Fires at Varying Height in a Corridor-Like Structure

Investigation on the burning behaviors of the combustible ceiling with the impingement of an incipient fire source

Upward Flame Spread over Discrete Thick Fuels under Mixed Convection Flow

Thermodynamic and Kinetic Characteristics of Combustion of Discrete Polymethyl Methacrylate Plates with Different Spacings in Concave Building Facades

Influences of sub-atmospheric pressure on downward flame spread over typical insulation material with parallel glass curtain wall structure in underground buildings

Flame Extension Lengths Beneath a Confined Ceiling Induced by Fire in a Channel with Longitudinal Air Flow

EXPERIMENTAL STUDY ON CHARACTERISTICS OF FLAME SPREAD OVER THE SURFACE OF WOOD SHEETS WITH DIFFERENT WIDTH UNDER DIFFERENT INCLINED ANGLE

Effect of solid surface curvature and wall heat loss on the downward flame spread along the edge of thin PMMA sheets

Experimental Study and Analysis on Flame Lengths Induced by Wall-Attached Fire Impinging Upon an Inclined Ceiling

Experimental Study of Upward Flame Spread Behaviors over Thermally Thick Vertical PMMA of Various Sample Widths under Normal Wind