Abstract:This paper presents an experimental investigation of the sample thickness effect on the concurrent flame steady spread behavior. Two configurations, ceiling flame and floor flame, as the fundamental diffusion combustion problems and representative scenarios of horizontal flame spread, are concerned herein. PMMA samples with thickness (delta) of 2, 3, 4, 5, 7, 9 mm were employed including both thermally-thin and thermally-thick conditions. A wind tunnel was used to provide the uniform concurrent airflow ranging from 0.3 m/s to 1.2 m/s in 0.3 m/s intervals. Flame characteristics and basic parameters to quantify the flame steady spread process have been studied, including flame spread rate (FSR), equivalent pyrolysis length as well as heat flux feedback in both pyrolysis and preheating zones. Results show that FSR decreases with sample thickness, being more sensitive to sample thickness for ceiling flame configuration than that for floor flame configuration. Equivalent pyrolysis length increases with sample thickness and ceiling flame's equivalent pyrolysis length is larger than floor flame's. Convection feedback is dominant under concurrent airflow regardless of the flame configuration, airflow velocity or sample thickness. In pyrolysis zone, the total heat flux to fuel surface of ceiling flame configuration is larger than that of floor flame configuration for thin samples due to buoyancy, but it decreases rapidly as sample thickness increases. In preheating zone, the heat flux decreases in power law for ceiling flame configuration while a piece-wise fitting is found for floor flame configuration, which is interpreted based on their inherent flame characteristic difference hence the thermal boundary layer conditions between these two configurations. To analyze the sample thickness effect on concurrent flame spread, a characteristic solid temperature (T*) is proposed by theoretical analysis, as an essential parameter to be used in the concurrent flame spread model to represent the coupling effect of heat input in gas phase and in-depth heat loss into the solid phase (or namely thermal inertia controlled by a characteristic thermal penetration depth). The calculated non-dimensional characteristic solid temperature (theta) shows to be less sensitive to flame configuration and concurrent airflow velocity for relatively thicker samples because the thermal penetration depth will tend to approach a limit. A general trend of its variation with sample thickness (delta) can be employed to predict the heat loss into solid phase and its predictive capability is verified by the experimental results. This work advances the fundamental understanding of the sample thickness effect on concurrent flame spread mechanism. (C) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Effect of the Sample Width and Concurrent Airflow Velocity on Heat and Mass Transfer Behaviors in Steady Flame Spread Stage

Effect of Sample Thickness on Concurrent Steady Spread Behavior of Floor- and Ceiling Flames

Local Flame And Flow Properties Of Propagating Premixed Turbulent Flames During Light-Round Process In A Micca-Type Annular Combustor

Experimental Study of Flame Spread over Thermally-Thin Inclined Fuel Surface and Controlling Heat Transfer Mechanism under Concurrent Wind

Experimental Investigation of the Flame Front Propagation Characteristic During Light-round Ignition in an Annular Combustor

Heat and Mass Transfer Mechanisms During Unsteady Flame Spread Process along Inclined Surface under Wind

Experimental Study of Upward Flame Spread Behaviors over Thermally Thick Vertical PMMA of Various Sample Widths under Normal Wind

Experimental study of flame spread transition from chemistry to heat transfer controlled regime at sub-atmospheric pressure: The effect of sample width

Effects of Sample Width on Flame Spread over Horizontal Charring Solid Surfaces on a Plateau

Transitional Flame-Spread and Fuel-Regression Behaviors under the Change of Concurrent Wind

Experimental Study on Coupled Combustion of PMMA Counter-directional Flame Spread in the Horizontal Direction

Fire Spread over Charring Materials: Influence of the Sample Orientation and External Radiant Intensity

EXPERIMENTAL STUDY ON CHARACTERISTICS OF FLAME SPREAD OVER THE SURFACE OF WOOD SHEETS WITH DIFFERENT WIDTH UNDER DIFFERENT INCLINED ANGLE

Effect of solid surface curvature and wall heat loss on the downward flame spread along the edge of thin PMMA sheets

Numerical Study on Opposed-Flow Flame Spread over Discrete Fuels – the Influence of Gap Size and Opposed-Flow Velocity

Experimental study on conical flame transfer functions considering velocity profiles

Influence of Preheating and Burner Geometry on Modeling the Attachment of Laminar Coflow CH4/air Diffusion Flames

Effect of Wall Heat Transfer on the Dynamics of Premixed Spherical Expanding Flames

Experimental study on the influence of restricted distance on the discrete flame spread of different widths

An Experimental Study and Analysis on Maximum Horizontal Extents of Buoyant Turbulent Diffusion Flames Subject to Relative Strong Cross Flows

Experimental Study on the Combustion Characteristics of Rectangular Fire Plumes