Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Critical Heat Flux of Highly Subcooled Water Flow Boiling in Circular Tubes with and Without Internal Twisted Tapes under High Mass Fluxes

A Critical Heat Flux Model for Saturated Flow Boiling on the Downward Curved Heated Surface

Prediction of Critical Heat Flux for Subcooled Flow Boiling in Annulus and Transient Surface Temperature Change at CHF

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Numerical study of heat transfer and fluid flow of supercritical water in twisted spiral tubes

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Experimental investigation and a mechanical model of critical heat flux in a narrow rectangular channel

Boiling curve of subcooled flow boiling of DI water from forced convection region until reaching CHF under different operation parameters in a vertical tube

Augmentation of Flow Boiling Critical Heat Flux along Microchanneled Surfaces

Observing Investigation of Boiling Characteristics Around CHF for the Downward Facing Heating Surface

An experimental study on critical heat flux for low flow and low pressure of water in a hexagonal 7-rod bundle channel

Enhancing the Critical Heat Flux Using Microchanneled Surfaces

Sensitivity analysis of geometrical parameters of supercritical water in twisted spiral tubes

Numerical investigation of critical heat flux during subcooled flow boiling in a vertical rectangular Mini-channel

THE EFFECT OF CHANNEL HEIGHT ON FLOW BOILING HEAT TRANSFER AND CHF IN FLAT MINICHANNELS WITH LOCAL HEATING

A CHF Correlation and Flow Pattern Observation on a Downward-Facing Boiling Surface

Investigation of flow boiling critical heat flux and heat transfer within a horizontally oriented channel with one-sided heating at three levels of subcooled inlet

The Effects of Surface Orientation, Heater Size, Wettability, and Subcooling on the Critical Heat Flux Enhancement in Pool Boiling

FLOW BOILING CRITICAL HEAT FLUX IN A SMALL TUBE FOR FC-72

Separate factors’ effects on CHF for flow boiling in an inclined rectangular channel under low mass flux

COMPARISON ANALYSIS OF CHF PARAMETRIC TRENDS IN VERTICAL TUBE AND 5 x 5 BUNDLE