Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Lamellar-interpenetrated Al–Si–Mg/SiC Composites Fabricated by Freeze Casting and Pressureless Infiltration

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration

Strengthening Mechanism and Damping Properties of SiCf/Al-Mg Composites Prepared by Combining Colloidal Dispersion with a Squeeze Melt Infiltration Process

Laser Powder Bed Fusion of Oxidized Microscale SiC-particle-reinforced AlSi10Mg Matrix Composites: Microstructure, Porosity, and Mechanical Properties

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Fabrication of 3D-SiC/aluminum alloy interpenetrating composites by DIW and pressureless infiltration

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Nano-Phase and SiC–Si Spherical Microstructure in SiC/Al-50Si Composites Solidified under High Pressure

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Microstructure and Mechanical Properties of Multi-Carbides/(al, Si) Composites Derived from Porous B4C Preforms by Reactive Melt Infiltration

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Processing of silica bonded porous SiC preform for metallic composites

Strengthening mechanism and anisotropy of mechanical properties of Si3N4p/Al-Mg-Si composites fabricated by sintering and extrusion

Mechanical and thermal expansion behavior of hybrid aluminum matrix composites reinforced with SiC particles and short carbon fibers

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Preparation and properties of ultralight fibrous β-Si3N4 3D scaffolds with honeycomb-like structure by directional freeze-casting