Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

A hierarchical nanolamella-structured alloy with excellent combinations of tensile properties

A Hierarchical and Multiphase Nanolaminated Alloy with an Excellent Combination of Tensile Properties

High Tensile Ductility and Strength in Dual-Morphology Hierarchical Nanolamellar-Structured Tizr Alloys

Simultaneously Enhancing Fracture Toughness and Strength in a Hierarchical Nanolamella-Structured Alloy

Simultaneously Enhancing the Strength and Ductility of Lamellar Ti–6Al–4V Alloy Via Designing Hierarchical 3D Nanolayered Structure

Designing ultra-strong and ductile hierarchical titanium alloys via interstitial solute-mediated multi-morphologic α-nanoprecipitates

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

A Novel High-Strength Β-Ti Alloy with Hierarchical Distribution of Α-Phase: the Superior Combination of Strength and Ductility

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy

Face Centered Cubic Substructure and Improved Tensile Property in a Novel Β Titanium Alloy Ti–5Al–4Zr–10Mo–3Cr

Hierarchical Structured Zn-Cu-Li Alloy with High Strength and Ductility and Its Deformation Mechanisms

Hierarchical nanostructured aluminum alloy with ultrahigh strength and large plasticity

Achieving super-high strength and acceptable plasticity for a near β-type Ti-4.5Mo-5.1Al-1.8Zr-1.1Sn-2.5Cr-2.9Zn alloy through manipulating hierarchical microstructure

Enhancing Mechanical Properties of Tizralv by Engineering A Multi-Modal-Laminated Structure

Hierarchical nano-martensite-engineered a low-cost ultra-strong and ductile titanium alloy

Tensile Brittleness and Ductility Improvement in a Novel Metastable Β Titanium Alloy with Lamella Structure

Synergetic Enhancement of Strength and Ductility Via a Heterogeneous Structure with Short-Range Clustering: A Novel Ti-V-Zr Medium Entropy Alloy

Microstructure evolution and mechanical properties of deformed TiZrAlV upon annealing

Enhancing Strength-Ductility Synergy Via Hierarchical Microstructure in Fine-Grained Ti-10Mo-8V-1Fe-3.5Al Alloy

Ultra-strong and ductile amorphous-crystalline Ti-Zr-Hf-Nb-Ta/Co-Ni-V nanolaminate thin films

Strength enhancement of a bi-lamellar PM Ti–6Al–4V alloy without sacrificing ductility by Al partitioning and twinning-induced plasticity effect