Abstract:Context: The mechanical characteristics and deformation behavior of Cu material under the nanoscratching through a diamond tooltip on the workpiece are studied using molecular dynamics (MD) simulation. Effects of scratching velocity, scratching depth, workpiece temperature, and grain size on the total force, shear strain, pile-up, shear stress, workpiece temperature, and phase transformation are investigated. The results reveal that increasing the scratching velocity leads to higher oscillation in total force, greater shear strain and shear stress, higher pile-up on the workpiece surface, and higher workpiece temperatures. The effect of the scratching velocity on phase transformation shows that most of the dislocation is a transformation structure from the FCC structure to the HCP, BCC, and other structures in all workpieces during the nanoscratching process. In addition, with increasing the scratching depth, material pile-up becomes more prominent, consequently elevating the contact area between the diamond tooltip and the workpiece, which simultaneously leads to an increase in total force, shear strain, pile-up, shear stress, and workpiece temperature. The MD simulation results revealed that the subsurface region of nanoscratched Cu single-crystal experiences the formation of stacking faults, vacancy defects, and cluster vacancies. In studying the effect of workpiece temperature, the results show that higher temperatures lead to the decline of scratching force, high plastic deformation, increased shear strain and stress, lower pile-up height, and high transition from the FCC structure to both other and BCC structures. For polycrystalline structures, the force curves occur in the oscillation state in all cases of different grain sizes because of the dislocation deformation during the cutting process. The maximum force decreases with diminishing grain size, attributed to the inverse Hall-Petch relation. As the grain size increases, leading to a decrease in the shear strain, stress, and an uneven pile up; also, the HCP structure rises with decreasing grain boundary and the partial dislocation and stacking fault mobilize inside grains. Methods: By using molecular dynamics (MD) simulation based on the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) software, all molecular interactions were described by the Lennard-Jones (LJ) and embedded atom method (EAM) potentials. In order to mitigate the effects of temperature fluctuations, the system employs an isothermal and isobaric (NPT) ensemble for precise temperature control. The temperature was set as 300 K and the time step was 1 fs (femtosecond).

Scratching of Copper with Rough Surfaces Conducted by Diamond Tip Simulated Using Molecular Dynamics

0701 Molecular Dynamics Simulation of Nano-Contact Between a Diamond Cutting Tool and a Copper Surface

Surface deformation of single crystalline copper on different nano-scratching paths

Nanoscale friction behavior and deformation during copper chemical mechanical polishing process

Molecular dynamics simulation on nanoindentation response of a copper workpiece

Orientation-dependent plastic flow in nanoscratching of copper surfaces

Coupled effect of scratching direction and speed on nano-scratching behavior of single crystalline copper

Molecular Dynamics Simulation of Single-Crystal 4H-SiC Nano Scratching with Different Scratching Directions of the Tool

Experimental Investigation at Relatively High Speed Scratching Induced by a Developed Diamond Tip

MOLECULAR DYNAMICS SIMULATION OF NANOSCALE FRICTION PROCESS

Molecular simulation of ultrasonic assisted diamond grit scratching 4H-SiC single-crystal

Molecular dynamics simulation of monocrystalline copper nano-scratch process under the excitation of ultrasonic vibration

Molecular dynamics simulation of subsurface damage mechanism during nanoscratching of single crystal silicon

Mechanical response of single-crystal copper under vibration excitation based on molecular dynamics simulation

Magnetic-Field-Assisted Scratching Process of Single-Crystal Copper

Molecular dynamics simulation of the material removal in the scratching of 4H-SiC and 6H-SiC substrates

Experimental Study on the Cutting Properties of Single Crystal Copper Anisotropic Surface in Micro-Nano Scale

Study on wear of diamond during scratching SiC using molecular dynamics simulations

Atomistic insights on the nanoscale single grain scratching mechanism of silicon carbide ceramic based on molecular dynamics simulation

Study of Effect of Indenter Shape in Nanometric Scratching Process Using Molecular Dynamics

Molecular dynamics study on the effect of electric current on electrically-assisted scratching for crystal copper