Abstract:Purpose– The purpose of this paper is to explore selective laser melting of yttria-stabilized zirconia (YSZ) ceramic by a 1 μm wavelength fibre laser; investigate the influence of different laser powers and different scanning velocities on the microstructure, the relative density, the deformation of ceramic sample and the micro-hardness; and analyze the crystal structure transformation during the fabrication.Design/methodology/approach– During the fabrication, the 5 mm × 5 mm × 5 mm YSZ ceramic samples are fabricated by rapid prototyping (RP) machine MCP Realizer SLM 250; density and microscopic photographs show the ceramic melting situation. The density of cubic sample with different laser powers and different scanning velocities is measured by Archimedes method. The microstructure of samples and powder is observed by SEM. The micro-hardness is measured by the Vickers micro-hardness equipment, and the crystal structure transition is studied by XRD.Findings– It is possible to melt YSZ powder completely with near-IR fibre laser, and the relative density of 5 mm × 5 mm × 5 mm cubic sample is 88 per cent, and the micro-hardness could reach 1,209 ± 262 HV500. The influence of laser power on the volume deformation is more sensitive than the scanning speed at the same energy density. The small pores and the obvious orderly cracks can be observed in the cross-section of sample; the uneven distribution of laser energy input is the main reason of the formation of orderly cracks. The transformation from monoclinic and cubic crystal to tetragonal crystal occurred during the melting process. Heat treatment (1400°C for 30 min) cannot significantly improve the density of the sample, but it can restore the colour of ceramic.Research limitations/implications– Particularly serious due to the deformation of the ceramic material, the authors cannot prepare a large ceramic sample and measure its macroscopic mechanical properties.Originality/value– This paper describes the manufacture of YSZ ceramic sample by SLM technology with a 1 μm wavelength fibre laser, and preliminary studies show the microscopic structure, distribution of laser parameters and crystal transformation.

Growth Characteristics of Ticxny Ceramics under Laser Melting Conditions

Effects of Laser Repetition Rate and Fluence on Micromachining of Tic Ceramic

Microstructure and fracture toughness of TiC-Ni cermets by direct laser fabrication

Competition Growth of Α and Β Phases in Ti-50 At.%al Peritectic Alloy During the Rapid Solidification by Laser Melting Technique

Columbite-rich Multiphase TiO2 Nanoceramic with Superior Mechanical and Dielectric Properties

Growth Morphologies and Mechanism of Tic in the Laser Surface Alloyed Coating on the Substrate of Tial Intermetallics

Investigations of the microstructure and performance of TiCp/Ti6Al4V composites prepared by directed laser deposition

Analysis of the growth mechanism of TiC crystal and the mechanical properties of the laser alloyed layer on the surface of pure titanium

Analysis of Growth Mechanism of Dendritic Titanium Carbides Produced by Laser Alloying of Pure Titanium with Graphite Powder

Regulating Nitrogen Fraction, Phasic Composition and Mechanical Properties in (ti0.2v0.2nb0.2ta0.2w0.2)(cxny) High-Entropy Ceramic Via Carbon Stoichiometry

Effect of Ni contents on the microstructure and mechanical properties of TiC–Ni cermets obtained by direct laser fabrication

Grain Growth and Hardness of Tic-Based Cermets: Experimental Investigation and Thermodynamic Calculations

Fabrication and Characterization of Micro-Channels on Al2O3/TiC Ceramic Produced by Nanosecond Laser

Microstructure and performance optimization of laser cladding nano-TiC modified nickel-based alloy coatings

Study on microstructure and tribological properties of nano/micron TiC/TC4 composites fabricated by laser melting deposition

High-Energy Ball-Milling Combined with Annealing of Tic Powders and Its Influence on the Microstructure and Mechanical Properties of the Tic-Based Cermets

Preparation and Characterization of Ti(C,N)-based Nano-Cermets

Study on the Phase Evolution, Microstructure and Densification Behavior of (Ti,m)(c,n)-Based Cermets

Microstructure Study on Selective Laser Melting Yttria Stabilized Zirconia Ceramic with Near Ir Fiber Laser

Oxide Scale Microstructure and Scale Growth Kinetics of the Hot-Pressed SiBCN-Ti Ceramics Oxidized at 1500 °C

Influence of Additive Silica on the Laser Melting of the Ceramic Coatings