Abstract:Metal additive manufacturing (AM) enables customizable, on-demand parts, allowing for new designs and improved engineering performance. Yet, the ability to control AM metal alloy microstructures (i.e., grain morphology, crystallographic texture, and phase content) is lacking. This work performs corroborative neutron diffraction and large-scale electron backscatter diffraction (EBSD) measurements to assess crystallographic texture in electron beam melted (EBM) Ti-6Al-4V as a function of scan strategy and build height. Texture components for one raster and two spot melt scan strategies were evaluated using a triclinic specimen symmetry to capture all possible texture components, which were found to be considerably different than previously reported values from studies employing orthotropic specimen symmetry. This finding highlights the importance of a standard method and best practice for assessing textures produced by AM. Texture was found to vary between scan strategies, but changed minimally as a function of build height. Parent phase β-Ti reconstructions obtained from as-built crystallographic orientations revealed spot melt scan strategies produced finer equiaxed/columnar grains with clear 001 β build direction fiber textures, whereas the raster scan strategy produced large columnar grains and a weaker 001 β build direction fiber texture. The observed grain morphologies agree with those predicted by solidification theory for the thermal gradients and solidification velocities experienced during the build process. The presence of a strong 001 β fiber orientation (typical of cubic solidification) produced by spot melting was found to correlate with a previously unreported 01 1 ¯ 2 α fiber texture in the as-built condition and colony microstructures. The 01 1 ¯ 2 α fiber texture was weakly observed for the raster scan strategy, and 001 β oriented grains preferentially transformed into α' martensite with orientations between 1 1 ¯ 00 α and 11 2 ¯ 0 α . This shift in product α-Ti orientations has not yet been reported, and further work is recommended to understand these crystallographic signatures in the context of solid-state phase transformations. The presence of the 01 1 ¯ 2 α fiber texture is proposed as a useful diagnostic for evaluating the solidification or transformed microstructure condition (e.g., grain morphology and texture) of Ti-6Al-4V AM builds via accessible techniques like laboratory X-ray diffraction.

Microstructure and texture evolution during the manufacturing of in situ TiC-NiCr cermet through selective laser melting process

EBSD investigation of microstructure and microtexture evolution on additively manufactured TiC-Fe based cermets—Influence of multiple laser scanning

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Effect of scanning strategies on the microstructure and mechanical properties of Ti–15Mo alloy fabricated by selective laser melting

Effect of laser parameters on microstructure and phase evolution of Ti-Si-C composites prepared by selective laser melting

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Microstructure and Phase Evolution of Ti-Al-C-Nb Composites Prepared by In Situ Selective Laser Forming

In-Situ SEM Study on Deformation and Failure Mechanism of TC4 Titanium Alloy by Laser Additive Manufacturing

Texture evolution as a function of scan strategy and build height in electron beam melted Ti-6Al-4V

Effect of Scanning Strategies on the Microstructure and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated through Selective Laser Melting

Evolution of microstructure and interfacial characteristics of complete solid-solution Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Microstructure Evolution of TiC Particles In Situ, Synthesized by Laser Cladding

Preparation of Ti2AlC through in-situ selective laser forming and reaction sintering

Grain Morphology Control and Texture Characterization of Laser Solid Formed Ti6al2sn2zr3mo1.5cr2nb Titanium Alloy

Microstructural evolution and phase transition mechanism of Ti(C,N)-based cermets during vacuum sintering process

In-situ synthesis of Ti<sub>5</sub>Si<sub>3</sub>-reinforced titanium matrix nanocomposite by selective laser melting: Quasi-continuous reinforcement network and enhanced mechanical performance

Microstructure and mechanical properties of (TiB+TiC)/Ti composites fabricated in situ via selective laser melting of Ti and B4C powders

Effect of nano-TiB2 particles on the anisotropy in an AlSi10Mg alloy processed by selective laser melting

Interfacial structures and strengthening mechanisms of in situ synthesized TiC reinforced Ti6Al4V composites by selective laser melting

Effect of Volume Energy Density on Selective Laser Melting Niti Shape Memory Alloys: Microstructural Evolution, Mechanical and Functional Properties