Abstract:In this work, the effect of a hydrothermal environment on mechanical properties and the electrical response behavior of continuous carbon fiber/epoxy (CFRE) composite produced by the pultrusion method were investigated. Due to the relatively uniform distribution of fibers and lack of resin-rich interlayer area, this effect for the pultruded CFRE composite plates is different from the common CFRE laminated composites. Firstly, its hygroscopicity behavior was studied. The absorption ratio increases rapidly to 1.02% within 3 days before reaching a relatively stable state. A three-point bending test, a Vickers hardness test, a thermogravimetric analysis (TGA), and a scanning electron microscope (SEM) analysis were performed to investigate the effect of the hydrothermal environment on the mechanical properties and thermal stability of the CFRE composite. The results indicated that the bending strength decreased quickly within 3 days of hydrothermal treatment, followed by a stable trend, which coincided with that of the hygroscopicity behavior of the composites. The fracture surface analysis indicated that the interfacial properties of carbon fibers in the epoxy matrix were decreased after the hydrothermal treatment, and more carbon fibers could be pulled out from the CFRE in the hygroscopic state. After the hydrothermal treatment, the micro-hardness of the composites was reduced by 25%. TGA confirmed the decreased thermal stability of the CFRE composites after the hydrothermal treatment as well. Moreover, the hydrothermally treated CFRE composites could a reach stable resistance response more readily. The revealing of the effect of moisture and hot environment on the mechanical properties and electrical response behavior of pultruded CFRE composites prepares the ground for their design and practical application in the corresponding environment.

Effect Of Heating Temperature On Microstructure And Mechanical Properties Of Continuous Copper Fiber

MICROSTRUCTURE OF AS-MELT SPUN Al-Cu-Mg-Fe-Ni ALLOY AND ITS VARIATION IN CONTINUOUS HEAT TREATMENT

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

Effects of Structural Parameters on the Thermal Insulation Properties of Coated Carbon Fiber Fabrics

Simulation of the Effects of Structural Parameters of Glass Fiber Fabric on the Thermal Insulation Property

Effect of Heating Rate on Morphology and Structure of Cofe2o4 Nanofibers

Effect of annealing processes on microstructure, mechanical properties and conductivity of Cu-12%Ag alloy composite-reinforced by fibers

Effects of Heat Treatment Temperature on Microstructure and Properties of Wiredrawn Cu-12ag Filamentary Composite

Effect of annealing temperature on microstructure and tensile properties of copper/aluminum composite thin strip

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Effect of Process Parameters on the Surface Quality, Microstructure and Properties of Pure Copper Wires Prepared by Warm Mold Continuous Casting

Effects of Different Heating and Cooling Rates during Solution Treatment on Microstructure and Properties of AA7050 Alloy Wires

Effect of Temperature on the Mechanical Properties, Conductivity, and Microstructure of Multi-layer Graphene/Copper Composites Fabricated by Extrusion

Effect of Temperature on Microstructure and Mechanical Properties of Fe-9Ni-2Cu Steel during the Tempering Process

Effect of Carbonization Temperature on Microstructures and Properties of Electrospun Tantalum Carbide/Carbon Fibers

Continuous Cooling Transformation Curves and Microstructures of Copper Bearing Low-Carbon Si-Mn Steel

Effect of Hydrothermal Environment on Mechanical Properties and Electrical Response Behavior of Continuous Carbon Fiber/Epoxy Composite Plates

Microstructure, mechanical properties and electrical conductivity of Cu–12wt.% Fe microcomposite annealed at different temperatures

Analysis of Tensile Failure Behavior of Metal Fiber Laminates Under Different Temperature Environments

Effect of Heat Treatment on Mechanical Properties of CuCrZr Triply Periodic Minimal Surface Structures Fabricated by Selective Laser Melting

Relationship among solution heating rate, mechanical properties, microstructure and texture of Al−Mg−Si−Cu alloy