Abstract:For aluminium alloys, precipitation strengthening is controlled by age-hardening heat treatments, including solution treatment, quenching, and ageing. In terms of technological applications, quenching is considered a critical step, because detrimental quench-induced precipitation must be avoided to exploit the full age-hardening potential of the alloy. The alloy therefore needs to be quenched faster than a critical cooling rate, but slow enough to avoid undesired distortion and residual stresses. These contrary requirements for quenching can only be aligned based on detailed knowledge of the kinetics of quench-induced precipitation. Until the beginning of the 21st century, the kinetics of relevant solid-solid phase transformations in aluminium alloys could only be estimated by ex-situ testing of different properties. Over the past ten years, significant progress has been achieved in this field of materials science, enabled by the development of highly sensitive differential scanning calorimetry (DSC) techniques. This review presents a comprehensive report on the solid-solid phase transformation kinetics in Al alloys covering precipitation and dissolution reactions during heating from different initial states, dissolution during solution annealing and to a vast extent quench-induced precipitation during continuous cooling over a dynamic cooling rate range of ten orders of magnitude. The kinetic analyses are complemented by sophisticated micro- and nano-structural analyses and continuous cooling precipitation (CCP) diagrams are derived. The measurement of enthalpies released by quench-induced precipitation as a function of the cooling rate also enables predictions of the quench sensitivities of Al alloys using physically-based models. Various alloys are compared, and general aspects of quench-induced precipitation in Al alloys are derived.

Evaluation of the Quenching Sensitivity of Al‐Zn‐Mg‐Cu‐Zr Aluminum Alloys by Mole Fraction of Equilibrium Phases

Influence of Mg Content on Quench Sensitivity of Al–Zn–Mg–Cu Aluminum Alloys

Study on quenching sensitivity of an Al–Zn–Mg–Cu alloy containing trace amounts of Sc and Zr

Influence of Quench-Induced Precipitation on Aging Behavior of Al-Zn-Mg-Cu Alloy

Quench rate sensitivity of age-hardenable Al-Zn-Mg-Cu alloys with respect to the Zn/Mg ratio: An in situ SAXS and HEXRD study

Quench sensitivity and microstructures of high-Zn-content Al−Zn−Mg−Cu alloys with different Cu contents and Sc addition

Study on Quench Sensitivity during Isothermal Treatment of 7A65 Aluminum Alloy

Effect of Processing Parameters on Quench Sensitivity of an AA7050 Sheet

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy

Influence of Grain Structure on Quench Sensitivity Relative to Localized Corrosion of High Strength Aluminum Alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Effect of rolling reduction on quench sensitivity of aluminium alloy 7A55

Quench Sensitivity of a 7A46 Aluminum Alloy

Effect of quenching rate on strengthening behavior of an Al-Zn-Mg-Cu alloy during natural ageing

Aging precipitation behavior and properties of Al–Zn–Mg–Cu–Zr–Er alloy at different quenching rates

Quench Sensitivity of Ultra-High Strength 7000 Series Aluminum Alloys

Microstructure evolution and quench sensitivity characterizations of Mg-9.5Gd-0.9Zn-0.5Zr alloy

Review of the Quench Sensitivity of Aluminium Alloys: Analysis of the Kinetics and Nature of Quench-Induced Precipitation

Detailed investigation of quench sensitivity of 2050 Al-Cu-Li alloy by interrupted quenching method and novel end quenching method

Quench sensitivity and microstructure evolution of the 2060 Al-Cu-Li alloy with a low Mg content

A Comparative Study on Precipitation Behavior of a Sand-Cast Al–Li–Cu Alloy with the Different Quenching Rates