Abstract:Uniaxial and cruciform biaxial tensile tests are performed on a face-centered cubic material AA6016-T4 and a body-centered cubic material DP490 under 19 different loading paths, i.e., uniaxial tension in seven directions and biaxial tension in rolling/transverse and 45°/135° directions, with seven and four stress ratios, respectively. The ability of several yield criteria to describe the plastic anisotropy for the tested materials, under the associated and non-associated flow rules is evaluated systematically. A new evaluation strategy to check the validity and applicability of the material models is proposed in this paper. This strategy is different from the traditional evaluation method in that the biaxial tensile mechanical properties measured in the 45°/135° sampling direction are included in the investigation scope, and it is not limited to the rolling/transverse sampling direction, i.e., the yield stress functions are evaluated by comparing the experimental and predicted uniaxial yield stresses, plastic work contours on the normal and diagonal planes. Further, the plastic potential functions are confirmed by the description accuracy of uniaxial rα-values and the directions of plastic strain rate in the rolling/transverse and 45°/135° directions. A new analytical calibration program is developed for the material parameters of the Poly6 yield criterion related to normal (a1,a2,...,a7) and shear stress components (a8,a9,...,a16), which can further introduce the yield stresses under the near plane strain states (σPS0, σPS45, and σPS90) and pure shear yield stress along the RD (τ0). The results indicate that the new calibration strategy of Analytical Poly6-II&2 can accurately describe the anisotropic yield behavior of the tested materials compared with other advanced yield criteria, especially for plastic work contours on the diagonal plane. Significant anisotropic yield behavior was observed under biaxial tensile stress states with the same loading ratio in different sampling directions, therefore, investigating the prediction accuracy of the biaxial tensile mechanical properties in only the rolling/transverse sampling direction is insufficient for evaluating the effectiveness of the material models; the mechanical properties at the initial yield point cannot fully reflect the plastic anisotropy of the materials. The material parameters of the Analytical Poly6-II&2 yield criterion are expressed as functions of equivalent plastic strain, which can continuously capture the evolution of the anisotropic yield behavior for AA6016-T4 and DP490. Three different calibration strategies of material parameter a16 do not affect the description ability of uniaxial tensile yield stresses, rα-values, and plastic work contours on the normal plane, but will change the calculation results of plastic work contours on the diagonal plane. When both τ0 and σPS45 are available, a more balanced prediction accuracy can be obtained.

CLASSIC STRAIN ENERGY FUNCTIONS AND CONSTITUTIVE TESTS OF RUBBER-LIKE MATERIALS

MULTIAXIAL STRAIN ENERGY FUNCTIONS OF RUBBERLIKE MATERIALS: AN EXPLICIT APPROACH BASED ON POLYNOMIAL INTERPOLATION

A unified expression of elastic-plastic notch stress-strain calculation in bodies subjected to multiaxial cyclic loading

Experimental Characterization and Finite Element Modeling the Deformation Behavior of Rubbers with Geometry Defects

Further Investigation of Neuber's Rule and the Equivalent Strain Energy Density (ESED) Method

Large deformation isotropic elasticity – on the correlation of theory and experiment for incompressible rubberlike solids

On the origin of Sanchez-Lacombe equation of state theory in hydrostatic strain energy model for rubber-like materials

A Physically-Based Hydrostatic Strain Energy Model for Rubber-Like Materials Inspired by Flory-Orwoll-Vrij Equation of State Theory

A Novel Planar Tension Test of Rubber for Evaluating the Prediction Ability of the Modified Eight-Chain Model under Moderate Finite Deformation

Large Strain Viscoelastic Constitutive Models for Rubber, Part II: Determination of Material Constants

On Modelling Simple Shear for Isotropic Incompressible Rubber-Like Materials

Energetically stable curve fitting to hyperelastic models based on uniaxial and biaxial tensile tests

A Strain Energy Function for Planar Response of a Constrained Cosserat Extensible Elastica with a General Reference Planar Shape

Anisotropic Hyperelastic Strain Energy Function for Carbon Fiber Woven Fabrics

The generalised Mooney space for modelling the response of rubber-like materials

A simple interpolation-based approach towards the development of an accurate phenomenological constitutive relation for isotropic hyperelastic materials

The Uniaxial Stress–Strain Relationship of Hyperelastic Material Models of Rubber Cracks in the Platens of Papermaking Machines Based on Nonlinear Strain and Stress Measurements with the Finite Element Method

Test and Characterization for the Incompressible Hyperelastic Properties of Conditioned Rubbers under Moderate Finite Deformation

On the Large Deformation Rubber-Like Materials: Constitutive Laws and Fem

CONSTITUTIVE PARAMETRIC EXPERIMENT OF TIRE RUBBER HYPERELASTIC LAWS WITH APPLICATION

Evolution of yield behavior for AA6016-T4 and DP490 - Towards a systematic evaluation strategy for material models