Abstract:Finite element analysis is extensively used in the design of rubber products. Rubber products can suffer from large amounts of distortion under working conditions as they are nonlinearly elastic, isotropic, and incompressible materials. Working conditions can vary over a large distortion range, and relate directly to different distortion modes. Hyperelastic material models can describe the observed material behaviour. The goal of this investigation was to understand the stress and relegation fields around the tips of cracks in nearly incompressible, isotropic, hyperelastic accouterments, to directly reveal the uniaxial stress–strain relationship of hyperelastic soft accouterments. Numerical and factual trials showed that measurements of the stress–strain relationship could duly estimate values of nonlinear strain and stress for the neo-Hookean, Yeoh, and Arruda–Boyce hyperelastic material models. Numerical models were constructed using the finite element method. It was found that results concerning strains of 0–20% yielded curvatures that were nearly identical for both the neo-Hookean, and Arruda–Boyce models. We could also see that from the beginning of the test (0–5% strain), the curves produced from our experimental results, alongside those of the neo-Hookean and Arruda–Boyce models were identical. However, the experiment’s curves, alongside those of the Yeoh model, converged at a certain point (30% strain for Pieces No. 1 and 2, and 32% for Piece No. 3). The results showed that these finite element simulations were qualitatively in agreement with the actual experiments. We could also see that the Yeoh models performed better than the neo-Hookean model, and that the neo-Hookean model performed better than the Arruda–Boyce model.

Novel Model for Uniaxial Strain‐rate–dependent Stress–strain Behavior of Ethylene–propylene–diene Monomer Rubber in Compression or Tension

Mechanical Behaviors of Copolymer Elastomers: Experimental Characterization and Constitutive Modelling

Phenomenological Modeling of the Stress-Stretch Behavior of EPDM Rubber with Loading-rate and Damage Effects

A Molecular Study on the Reinforcement of Polymethylene Elastomers

One-Dimensional Dynamic Compressive Behavior of EPDM Rubber

A rate-dependent aging constitutive model of EPDM rubber

Experimental Characterization and Finite Element Modeling the Deformation Behavior of Rubbers with Geometry Defects

A Molecular Model of the Elastic Behavior of Polymethylene Chains

Constitutive Model for Thermal-Oxygen-Aged EPDM Rubber Based on the Arrhenius Law

Tension responses of carbon black filled rubbers at intermediate and high strain rates: Experimental investigation and modeling

Visco‐elasto‐plastic constitutive model of adhesives under uniaxial compression in a range of strain rates

A three-dimensional constitutive model for the large stretch behavior of rubber elastic materials

Modeling the Rate-Dependent Ductile-Brittle Transition in Amorphous Polymers

A Unified Micromechanical Model for the Mechanical Properties of Two Constituent Composite Materials. Part IV: Rubber-Elastic Behavior

A constitutive model for poly-methyl-methacrylate over a wide range of strain rates and temperatures

Evaluation of Crosslink Density Using Material Constants of Ethylene-Propylene-Diene Monomer/Styrene-Butadiene Rubber with Different Nanoclay Loading: Finite Element Analysis-Simulation and Experimental

Mooney-Rivlin Parameter Determination Model as a Function of Temperature in Vulcanized Rubber Based on Molecular Dynamics Simulations

The Uniaxial Stress–Strain Relationship of Hyperelastic Material Models of Rubber Cracks in the Platens of Papermaking Machines Based on Nonlinear Strain and Stress Measurements with the Finite Element Method

A gradient-extended thermomechanical model for rate-dependent damage and failure within rubberlike polymeric materials at finite strains

Experimental Investigation and Constitutive Modeling of Uncured Carbon Black Filled Rubber at Different Strain Rates

Effect of the temperature and strain rate on the tension response of uncured rubber: Experiments and modeling