Abstract:The turntable is generally divided into an inertial test bench and a simulation turntable for calibration, performance testing, and semi-physical simulation of aircraft guidance products [1, 2], testing the attitude angle variation of a single carrier or the relative motion between multiple carriers, the docking process, and other parameters [3, 4]. In 1954, the turret developed by the Massachusetts Institute of Technology used photoelectric angle–measuring sensors and precision bearings, which improved the precision greatly and hence was put into production [5, 6]. At present, the domestic and international turntables have high precision and fast response, providing high calibration accuracy and accurate performance detection for the calibration and testing of inertial navigation components [7, 8]. With the advancement of industrial control technology, the turntable has been rapidly developed [9, 10]. In 2013, the five-axis flight simulation turret developed by Acutronic has successfully been able to meet the high-precision requirements for testing high-dynamic missile performance. The turntable is a high-precision turntable for seeker testing. The rotary table is driven by an ultrasonic motor to ensure the nonmagnetic and high-precision requirements of the turntable [11, 12]. Ultrasonic motors use the linear effects of piezoelectric materials to achieve linear or rotational motion through frictional coupling. They do not distort the magnetic field and achieve high precision [13, 14]. The turntable uses ceramic bearings to ensure rotational accuracy. The support method adopts an adjustable threelegged positioning. A level is installed on the bottom plate to observe whether the turntable is installed horizontally. The turntable is equipped with a very high precision grating encoder to ensure that the measurement accuracy is higher than the control accuracy. In this study, the pointing accuracy of the turntable was studied. The influence of the grating installation error on the accuracy detection was also analyzed. The steadystate error of the turntable has an important influence on the motion accuracy of the turntable. Finally, the influence of the control parameters on the steady-state error of the turntable was analyzed. The positioning accuracy and control parameters of the two-axis precision nonmagnetic turntable were obtained, and the PID adjustment was introduced to make the accuracy index of the nonmagnetic turntable meet the requirements. The turntable could realize a nonmagnetic working environment and achieve the high precision required by the index under the driving of the ultrasonic motor [15]. 2. Two-axis precision turntable control system construction and index requirements

Development of ultra-precision centering and leveling turntable using aerostatic bearing technology

Design and Servo Control for Precision Opto-Electronic Tracking Turntable

A New Principle and Device for Large Aircraft Components Gaining Accurate Support by Ball Joint

A Liquid-Surface-Based Three-Axis Inclination Sensor for Measurement of Stage Tilt Motions

Design of a Novel Air Bearing Workbench for Rotary Ultrasonic Drilling of Advanced Ceramics

The Design Study of Single Plane Vertical Hard Bearing Dynamic Balancing Machine

Error Analysis Of Spherical Ultra-Precision Measurement

Design And Dynamic Analysis Of A Micro Three-Axis Turntable

Design, Control of an Aerostatic X-Y Planar Motion Stage for Precision Positioning

Precision tilting platform used for static calibration of accelerometers

Development of submicron precision three-dimensional low cross-interference air-floating motion stage

Accuracy Analysis and Motion Control of Two-axis Nonmagnetic Turntable Based on Ultrasonic Motor

Research of three-dimensional precision air-bearing stage with small rotatory error

Non-contact ultra-precision metrology of superfine cylinders with a developed two-dimensional coordinate measuring device

Design and characteristics of a new aerostatic bearing stylus sensor for surface measurement

Decoupling Method for Four-Degree-of-freedom Automatic Centering and Tilting Worktable

Development of Precision Blank Carriage for Manufacturing Large Gratings and Echelles

Design of a Large Aperture High-Precision Four-Dimensional Adjustment Table

Development of ultra-precision three axes micro milling machine

Design and Implementation of an Active Rectangular Aerostatic Thrust Bearing Stage with Electromagnetic Actuators

Measurement and Characterization of Rotational Errors of Aerostatic Bearings in Subnanometer Accuracy