Abstract:In order to support the high growth of Artificial Intelligence, Internet of Things, Industrial IOT, Cloud Service and 5G, the IC (Server/Router/Switch) needs higher/faster performance to collect, store, commute and transmit a mass of data. Therefore, the I/O (input/output) density of IC will increase with the silicon nodes < 5 nm, fine pitch $mu ext{bump}$, and fine line width/space substrate. However, the solder reflow of IC faces two problems of the chip damages (silicon nodes: current leakage, highly electromigration; ELK (extremely low-k): current leakage, crack) and solder high stress (solder: wicking, IMC (intermetallic compound)) due to highly thermal budget of MR (mass reflow). In this paper, LAB (laser assisted bonding) will replace MR (mass reflow) to solve these problems. In this study, a test vehicle with the size of $55^{ast}55 ext{mm}2$ FCBGA (flip chip ball grid array) was built. Two types (A and B) of substrate were applied to the FCBGA, with the differences between the solder mask (thickness, surface brightness/roughness) and substrate mass. LAB uses a semiconductor laser with wavelength of 980 nm, and the area of laser beam is 91.5% of the substrate area. The study is divided into three parts. For the first part, the surface temperature of die without substrate is higher than that of die with substrate at the same parameters about 187.2 °C. The result shows that the substrate has the function of heat storage. In addition, for the surface temperature of die with substrate, the result shows that all solders melt at 2.82 sec, and the surface temperature of the center of die is 22.8 °C lower than the four corners of it. Then the delta temperature between the surface temperature of the center of die and bump is 48.3 °C. The result shows that the overall temperature of die with substrate is not uniform. Next, for substrate effect, the surface temperature of die and B substrate is lower than that of die and A substrate based on the following reasons: for the solder mask, (a) the surface brightness of B substrate is 11% higher than that of A substrate result in an increase of the reflected light; (b) the roughness of B substrate is 26% lower than that of A substrate result in an increase of the reflected light; (c) the thickness of B substrate is 23% lower than that of A Substrate result in a reduction of Absorbed light; for substrate mass (d) the weight of B substrate is 10% higher than that of A substrate. Finally, the assembled FCBGA packages by LAB passed reliability tests: MSL4 pre-conditioning with uHAST 168 hours, TCT B 1000 thermal cycles and HTST 1000 hours. Details of the results are presented and discussed in the paper. In summary, we have developed the parameter set to solve it in different substrates and predicted the melting time of solder and temperature profile of die surface. Therefore, LAB (laser assisted bonding) can successfully solve the problems MR encounters. The full descriptions of the development results will be discussed in this study.

Back-Side Wafer Grinding Quality Affecting Back-End Assembly Process for LCD Driver ICs

Investigation of Dicing Saw Methods Impacting Back-End Assembly Process

Optimizing the dicing saw parameters of 60 μm wafer dicing street

EFFECT OF WAFER EDGE CUT ON TESTING AND YIELD

Avoidance of Bonding Pad Contamination Affecting Back-End Assembly Process

Optimal design of wafer back-grinding feeding profile considering subsurface damage and productivity

Interface failure behavior and mechanisms of 4H-SiC wafer with alloy backside layer caused by different dicing technologies

Subsurface Damage and Bending Strength Analysis for Ultra-Thin and Flexible Silicon Chips

Analysis of Linewidth Uniformity and Line Edge/Width Roughness in a 5 Nm Logic SAQP Process

Effect of Blade Dicing Parameters on Die Strength

Integrated Process for Silicon Wafer Thinning

Process optimization of preparing CMOS backplane for ultrahigh pixel density red Micro-LED display

The Study of Packaging Substrate Effect in FCBGA by Laser Assisted Bonding

ECR Plasma-Enhanced Au/Al Bondability in Fine-Pad-Pitch BGA Assembly

Si Characterization on Thinning and Singulation Processes for 2.5/3D HBM Package Integration

Laser Grooving Technology Study at Dicing Process in Wafer Level Package

The Influence of Sub-surface Damage Microstructure on Ultra-thin Die Flexural Strength

Methods of Reducing Metal Damager Defect in Back End of Line for Semiconductor in 28nm Technology

P‐8.4: Research on Chip Layout Design and Printing Process Optimization of Mini‐LED Light Board

A Numerical Technique to Evaluate Warpage Behavior of Double Sided Rigid-Flex Board Assemblies during Reflow Soldering Process

Advances in Panel Scalable Planarization and High Throughput Differential Seed Layer Etching Processes for Multilayer RDL at 20 Micron I/O Pitch for 2.5D Glass Interposers