Fast and Highly Sensitive Humidity Sensors Based on NaNbO3 Nanofibers

Youdong Zhang,Xumin Pan,Zhao Wang,Yongming Hu,Xiaoyuan Zhou,Zhenglong Hu,Haoshuang Gu

DOI: https://doi.org/10.1039/c5ra00205b

IF: 4.036

2015-01-01

RSC Advances

Abstract:A humidity sensor based on NaNbO3 nanofiber networks with fast, ultra-sensitive and selective room-temperature response was fabricated through electrospinning process.

What problem does this paper attempt to address?

A RESISTIVE-TYPE NANOSTRUCTURED HUMIDITY SENSOR PREPARED BY ELECTROSPINNING

Li Peng,Yang Mujie

DOI: https://doi.org/10.3969/j.issn.1000-2278.2008.03.009

2008-01-01

Journal of Ceramics

Abstract:In this paper, nanofibers composed of polyaniline, silicon-containing polyelectrolytes and PEO were deposited on interdigitated gold electrodes by electrospinning to construct a humidity nanosensor. The resistance of the nanosensor changed for three orders of magnitude in the humidity range of 22 -95% RH, indicating a high sensitivity. In addition, it showed good linearity (R2=0.966) on a semi-logarithmic scale, very small hysteresis (2% RH) and fast response time (t90%: 7s and 19s for adsorption and desorption, respectively). Moreover, the decoration of electrode with polyelectrolyte is proved to effectively improve the contact between the nanofibers and the gold electrode.
High-sensitivity fiber-optic humidity sensor based on microfiber overlaid with niobium disulfide

Enze Zhang,Dongqin Lu,Shuo Zhang,Xun Gui,Heyuan Guan,Zilong Zhang,Yijin Lin,Jingyuan Ming,Jiyu Hong,Jiangli Dong,Xiaoli Wang,Wentao Qiu,Wenguo Zhu,Jianhui Yu,Huihui Lu,Zhe Chen

DOI: https://doi.org/10.1007/s10853-020-05230-0

IF: 4.5

2020-09-11

Journal of Materials Science

Abstract:Humidity sensors by exploiting transition metal dichalcogenides have attracted enormous attention in various applications. Here, we demonstrate a high-sensitivity fiber-optic humidity sensor based on microfibers overlaid with niobium disulfide (NbS<sub>2</sub>). Our experimental results show that this type of humidity sensor has high sensitivity, and good repeatability and reversibility. In the RH range of 72–97%, a sensitivity of up to 1.05 dB/RH% and an excellent linearity correlation of 99.5% were achieved. The transmission spectrum of the humidity sensor indicates that this sensor has a wide wavelength detection range from 1530 to 1565 nm. We applied the sensor to monitor human breath with a fast response. We anticipate that the humidity sensor will be useful for the environmental monitoring, food production, and semiconductor industries.

materials science, multidisciplinary
A Fast Humidity Sensor Based on Li+-Doped SnO2 One-Dimensional Porous Nanofibers

Min Yin,Fang Yang,Zhaojie Wang,Miao Zhu,Ming Liu,Xiuru Xu,Zhenyu Li

DOI: https://doi.org/10.3390/ma10050535

IF: 3.4

2017-05-16

Materials

Abstract:One-dimensional SnO₂- and Li⁺-doped SnO₂ porous nanofibers were easily fabricated via electrospinning and a subsequent calcination procedure for ultrafast humidity sensing. Different Li dopant concentrations were introduced to investigate the dopant's role in sensing performance. The response properties were studied under different relative humidity levels by both statistic and dynamic tests. The best response was obtained with respect to the optimal doping of Li⁺ into SnO₂ porous nanofibers with a maximum 15 times higher response than that of pristine SnO₂ porous nanofibers, at a relative humidity level of 85%. Most importantly, the ultrafast response and recovery time within 1 s was also obtained with the 1.0 wt % doping of Li⁺ into SnO₂ porous nanofibers at 5 V and at room temperature, benefiting from the co-contributions of Li-doping and the one-dimensional porous structure. This work provides an effective method of developing ultrafast sensors for practical applications-especially fast breathing sensors.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Ultrafast Response Humidity Sensor Based on Electrospun Porous BaTiO3 Nanofibers

Hong Di Zhang,Chen Hao Sheng,Bin Sun,Yun Ze Long

DOI: https://doi.org/10.4028/www.scientific.net/amm.319.43

2013-01-01

Applied Mechanics and Materials

Abstract:Nanocrystalline and porous barium titanate (BaTiO3) nanofibers with diameter 200-400 nm were synthesized via electrospinning and followed calcinations. The morphology and microstructure of the nanofibers were characterized using field emission scanning electron microscope, X-ray diffractometer and transmission electron microscope, respectively. And the electrical and humidity sensing properties of the nanofibers were also measured. The results reveal that the BaTiO3 nanofibers have a conductivity of about 0.3 S/cm, and show an ultrafast response time (~0.7 s) and a recovery time (~0.4 s) to humidity at room temperature. In addition, the sensing mechanism was also discussed briefly based on its nanocrystalline and porous microstructure of the electrospun material.
QCM-based Humidity Sensor and Sensing Properties Employing Colloidal SnO2 Nanowires

Naibo Gao,Hua-Yao Li,Wenhui Zhang,Yuzhu Zhang,Yi Zeng,Zhixiang Hu,Jingyao Liu,Jianjun Jiang,Ling Miao,Fei Yi,Huan Liu

DOI: https://doi.org/10.1016/j.snb.2019.05.009

IF: 9.221

2019-01-01

Sensors and Actuators B Chemical

Abstract:In this paper, a quartz crystal microbalance (QCM)-based humidity sensor has been fabricated by colloidal fin oxide (SnO2) nanowires. The SnO2 nanowires were synthesized via a colloidal process that employing SnCl4 ethanol solutions mixed with oleic acid (OA) and oleylamine (OLA). The spin-coating method was chosen to deposit the sensitive film at room temperature without high-temperature sintering. Furthermore, the Cu(NO3)(2) methanol solution was used to remove the organic long chains coated on the surface of the colloidal SnO2 nanowires and expose more adsorption sites. The characterizations of the material were studied by means of FTIR, XRD, and FE-SEM. The saturated salt solution method was used to investigate the humidity sensing performance (response, recovery, repeatability, etc.) of the QCM sensor in the range of 11%-97%. The results showed that the sample with 12 h synthesis has the best humidity response. This may be attributed to the larger specific surface area which makes the material provide more adsorption sites for water molecules, and more (110) planes formed which could absorb more water molecules proved by the Density Functional Theory (DFT) calculation.
Highly Sensitive and Ultrafast Response Surface Acoustic Wave Humidity Sensor Based on Electrospun Polyaniline/poly(vinyl Butyral) Nanofibers.

Qianqian Lin,Yang Li,Mujie Yang

DOI: https://doi.org/10.1016/j.aca.2012.08.041

IF: 6.911

2012-01-01

Analytica Chimica Acta

Abstract:Polyaniline (PANi) composite nanofibers were deposited on surface acoustic wave (SAW) resonator with a central frequency of 433MHz to construct humidity sensors. Electrospun nanofibers of poly(methyl methacrylate), poly(vinyl pyrrolidone), poly(ethylene oxide), poly(vinylidene fluoride), poly(vinyl butyral) (PVB) were characterized by scanning electron microscopy, and humidity response of corresponding SAW humidity sensors were investigated. The results indicated that PVB was suitable as a matrix to form nanofibers with PANi by electrospinning (ES). Electrospun PANi/PVB nanofibers exhibited a core–sheath structure as revealed by transmittance electron microscopy. Effects of ES collection time on humidity response of SAW sensor based on PANi/PVB nanofibers were examined at room temperature. The composite nanofiber sensor exhibited very high sensitivity of ∼75kHz/%RH from 20 to 90%RH, ultrafast response (1s and 2s for humidification and desiccation, respectively) and good sensing linearity. Furthermore, the sensor could detect humidity as low as 0.5%RH, suggesting its potentials for low humidity detection. Attempts were done to explain the attractive humidity sensing performance of the sensor by considering conductivity, hydrophilicity, viscoelasticity and morphology of the polymer composite nanofibers.
Facile Fabrication of Nylon66/Multi-Wall Carbon Nanotubes/Polyvinyl Alcohol Nanofiber Bundles for Use as Humidity Sensors

Yanhui Yang,Zhongzhu Liu,Guoqiang Zheng,Kun Dai,Chunguang Shao,Chuntai Liu,Qian Li,Liwei Mi,Changyu Shen

DOI: https://doi.org/10.1080/00222348.2020.1855790

2020-12-09

Abstract:<span>Currently used humidity sensors have a large size which seriously hinders their applications in many special fields. Therefore, a facile way for fabricating miniaturized humidity sensors is desired. In this work a high-performance, nanofiber bundle sensor (NfBS) was fabricated through immersing nylon66 (PA66)/multiwall carbon nanotubes (MWCNTs) nanofiber bundles into a polyvinyl alcohol solution. In the PA66/MWCNTs nanofiber bundles the MWCNTs were absorbed on the surfaces of the PA66 nanofibers. The NfBS exhibited a wide range of 11–85% relative humidity (RH) sensitivity with a fast response-recovery time as well as small hysteresis and good repeatability, but had an extremely small size (about 0.1 mm in diameter and 2 mm in length) due to the unique advantages of nanofiber bundles. In addition, the NfBS showed good performance in monitoring human breath. The results in this study provide a promising opportunity and a good method for manufacturing mini-humidity sensors with smaller sizes for electronic products.</span>
High sensitivity Optical Humidity Sensing Based on Polymer Microfiber Cavity Coupled Metallic Nanorod

Ning Zhou,Pan Wang,Zhangxing Shi,Xin Guo,Jianrong Qiu,Limin Tong

DOI: https://doi.org/10.1109/acp.2018.8596238

2018-01-01

Abstract:We demonstrate a high-sensitivity humidity sensor taking advantage of single-band ultranarrow plasmon resonance of a single Au nanorod coupling to a whispering gallery cavity of a polyacrylamide microfiber. (Abstract)
Humidity Sensors Using in Situ Synthesized Sodium Polystyrenesulfonate/zno Nanocomposites.

Y Li,MJ Yang,Y She

DOI: https://doi.org/10.1016/j.talanta.2003.09.011

IF: 6.1

2004-01-01

Talanta

Abstract:Thin film humidity sensors have been prepared using in situ synthesized inorganic/organic nanocomposites of sodium polystyrenesuffonate (NaPSS) and ZnO. Its humidity sensing characteristics and the sensing mechanism have been investigated by measuring the complex impedance spectra of the sensor at different humidities. The logarithm of the impedance of sensor based on composite film changes linearly by four-orders of magnitude over almost whole humidity range (11-97% RH). Furthermore, the sensor exhibits a quick response (absorption: 2 s, desorption: 2 s) and small hysteresis (less than 2% RH). The composite film shows better sensing properties than NaPSS film, such as better linearity, quicker response. Explanation to the improvement is attempted by taking into account of the composition and structure of the nanocomposites. (C) 2003 Elsevier B.V. All rights reserved.
Electrospun nanofibers of polymer composite as a promising humidity sensitive material

Peng Li,Yang Li,Bangyu Ying,Mujie Yang

DOI: https://doi.org/10.1016/j.snb.2009.07.006

2009-01-01

Abstract:Nanofibers of a composite of a silicon-containing polyelectrolyte, polyethylene oxide and polyaniline (PANI) were obtained by electrospinning and heat treatment. The morphologies of the composite nanofibers were characterized by scanning electron microscopy, which showed that the nanofibers with a diameter of 250–500nm formed a non-woven mat with highly porous structure. It was found that the polymer composite nanofibers showed impedance change from 6.3×106 to 2.5×104Ω with the increment of relative humidity (RH) from 22 to 97% at room temperature, exhibiting high sensitivity and good linearity on a semi-logarithmic scale. In addition, they exhibited fast and highly reversible response characterized by very small hysteresis of ∼2% RH and short response time (t90%: 7s and 19s for adsorption and desorption between 33 and 97%RH, respectively). The modification of the electrode with poly(diallyldimethylammonium chloride) prior to the deposition of nanofibers improved their humidity response, which may be related to the enhanced contact between the nanofibers and underlying substrate. The effect of PANI on the humidity response of the composite nanofibers was also investigated, and it was found that PANI effectively decreased the impedance of the nanofibers. The electrospun polymer composite nanofibers may find applications in the preparation of high performance humidity sensors.
Humidity Sensors Based on ZnO/TiO2 Core/shell Nanorod Arrays with Enhanced Sensitivity

Lei Gu,Kaibo Zheng,Ying Zhou,Juan Li,Xiaoliang Mo,Greta R. Patzke,Guorong Chen

DOI: https://doi.org/10.1016/j.snb.2010.12.024

IF: 9.221

2010-01-01

Sensors and Actuators B Chemical

Abstract:Highly aligned arrays of ZnO/TiO2 core/shell nanorods were fabricated on glass substrates by hydrothermal growth of ZnO nanorods cores followed by the deposition of anatase TiO2 shells in a sol-gel process. The characterization of these composite materials with scanning electron microscopy (SEM), Raman spectroscopy, X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX) and transmission emission microscopy (TEM) points to the formation of crystalline ZnO nanorod cores that are coated with anatase TiO2 shells. Humidity sensors based on these core/shell nanorod arrays exhibit outstanding sensitivities with capacitances varying from 10(1) to 10(6) pF over a relative humidity (RH) range of 11%-95% at room temperature, which is 1.5 and 3 orders of magnitude higher than that of pristine TiO2 films and ZnO nanorods, respectively. Complex impedance analysis indicated that the enhanced humidity sensitivity is probably due to the high surface/volume ratio of this core/shell material in combination with the remarkable hydrophilicity of the TiO2 shell. (C) 2011 Elsevier B.V. All rights reserved.
High-temperature humidity sensors based on WO3–SnO2 composite hollow nanospheres

Daoping Cai,L. Mei,Lingling Wang,Taihong Wang,Q. Li,Han Li,B. Liu,Dandan Wang,Yanrong Wang,Yuan Liu

DOI: https://doi.org/10.1039/C4TA00363B

2014-04-15

Abstract:Three kinds of humidity sensors were fabricated from WO3–SnO2 composite hollow nanospheres (WO3–SnO2 HNS), WO3 nanoparticles (WO3 NPs) and SnO2 nanoparticles (SnO2 NPs). WO3–SnO2 HNS were prepared by a facile hydrothermal process with a diameter and thickness of about 550 nm and 30 nm, respectively. Temperature-dependent properties of as-prepared humidity sensors were investigated at various values of relative humidity and temperature. It was found that the WO3–SnO2 HNS humidity sensor showed good performance at 80 °C. The response time, recovery time and sensitivity were evaluated while switching the humidity between 35% RH and 98% RH. The response time decreased from 289 to 29 s, the recovery time reduced from 22 to 8 s, and the sensitivity changed from 16.2 to 11.4 as the work temperature was raised from 24 to 80 °C. An opposite humidity sensing phenomenon was observed between WO3 NPs and SnO2 NPs at a high temperature, which might explain the temperature-dependent properties of the WO3–SnO2 HNS humidity sensor. This work could stimulate a right approach to design practical humidity sensors with high sensitivity, long stability and fast response.

Materials Science
A Flexible Humidity Sensor Based on Co3O4 Nanoneedles with High Sensitivity and Quick Response

Qi,Qi Wang,Nanliu Liu,Xiaoping Zheng,Xiongjie Ding,Zhiwen Liang,Qing Wang,Guoyi Zhang

DOI: https://doi.org/10.1166/jno.2020.2788

2020-01-01

Journal of Nanoelectronics and Optoelectronics

Abstract:A flexible humidity sensor has been realized based on Co3O4 nanoneedles via a deposition technique. High humidity sensing and excellent flexible properties are observed in the tests. The impedance of the as-prepared sensor decreases by nearly three orders of magnitude with increasing relative humidity (RH) from 11% to 95% on a semilogarithmic scale. The response and recovery times are about 3 and 6 s respectively. The maximum hysteresis is less than 4% under 80% RH. No obvious changes for the sensing performance can be obtained after 100 bending/extending cycles and bending tests. These performances make the current sensor a good candidate for flexible humidity detection.
Graphitic Carbon Nitride Nanosheets Deposited on Microfibers for Relative Humidity Sensing

Zhengyu Yan,Caoyuan Wang,Ruowei Yu,Zixian Hu,Limin Xiao

DOI: https://doi.org/10.1364/acpc.2020.m4a.50

2020-01-01

Abstract:Graphitic carbon nitride nanosheets deposited on microfibers for relative humidity sensing is first demonstrated with high sensitivity. Fast response time of 0.43 s and recovery time of 0.87 s are characterized.
Ultrafast Self-Assembly MoS2/Cu(OH)2 Nanowires for Highly Sensitive Gamut Humidity Detection with an Enhanced Self-Recovery Ability.

Jianbin Lin,Han Fang,Xianhua Tan,Bo Sun,Ziyi Wang,Huidan Deng,Huan Liu,Zirong Tang,Guanglan Liao,Tielin Shi

DOI: https://doi.org/10.1021/acsami.9b17155

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Humidity sensors have attracted intense interest in various fields because of the importance of humidity detection. Different methods have been adopted to enhance sensing performances of humidity sensors, while it is challenging for researchers to avoid the invalidation of the sensors after being wet. Here, we, for the first time, introduce self-assembly MoS2/Cu(OH)2 nanowires fabricated by liquid self-spreading-coating-evaporating as sensing materials and present MoS2/Cu(OH)2 nanowire-based quartz crystal microbalance gamut humidity sensors with superior sensitivity and self-recovery ability. The sensors deliver a remarkable sensitivity (60.8 Hz/% RH) under a wide range (0-97% RH) with fast response (1.9 s)/recovery time (3.8 s) and upgrade self-recovery ability that can maintain their original performances even after being wet, frozen, and heated or immersed in water. The sensors are also employed to monitor water counting, dew alarming, and human breathing (within 4 s), further showing their ultrahigh sensitivity for water molecules. The underlying humidity-sensing mechanism is interpreted by density functional theory calculations and in-situ Fourier transform infrared spectra experiments adequately, revealing that the high sensing performances are attributed to abundant adsorption sites and physisorption of water molecules. Our work proposes a strategy for transferring materials to arbitrary nanostructures swiftly and demonstrates new perspectives for highly sensitive humidity detection as well as self-recovery ability.
Flexible and Highly Sensitive Humidity Sensor Based on Sandwich-Like Ag/Fe3O4 Nanowires Composite for Multiple Dynamic Monitoring

Maojiang Zhang,Minglei Wang,Mingxing Zhang,Long Qiu,Yinjie Liu,Wenli Zhang,Yumei Zhang,Jiangtao Hu,Guozhong Wu

DOI: https://doi.org/10.3390/nano9101399

IF: 5.3

2019-10-01

Nanomaterials

Abstract:Functional textiles with unique functions, including free cutting, embroidery and changeable shape, will be attractive for smart wear of human beings. Herein, we fabricated a sandwich-like humidity sensor made from silver coated one-dimensional magnetite nanowire (Fe3O4 NW) arrays which were in situ grown on the surface of modified polypropylene nonwoven fabric via simultaneous radiation induced graft polymerization and co-precipitation. The humidity sensor exhibits an obvious response to the relative humidity (RH) ranging from RH 11% to RH 95% and its response value reaches a maximum of 6600% (ΔI/I0) at 95% relative humidity (RH). The humidity sensor can be tailored into various shapes and embroidered on its surface without affecting its functionalities. More interesting, the intensity of its response is proportional to the size of the material. These features permit the sensor to be integrated into commercial textiles or a gas mask to accurately monitor a variety of important human activities including respiration, blowing, speaking and perspiration. Moreover, it also can distinguish different human physical conditions by recognizing respiration response patterns. The sandwich-like sensor can be readily integrated with textiles to fabricate promising smart electronics for human healthcare.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
A highly sensitive humidity sensor based on a nanofibrous membrane coated quartz crystal microbalance

Xianfeng Wang,Bin Ding,Jianyong Yu,Moran Wang,Fukui Pan

DOI: https://doi.org/10.1088/0957-4484/21/5/055502

IF: 3.5

2010-02-05

Nanotechnology

Abstract:A novel humidity sensor was fabricated by electrospinning deposition of nanofibrous polyelectrolyte membranes as sensitive coatings on a quartz crystal microbalance (QCM). The results of sensing experiments indicated that the response of the sensors increased by more than two orders of magnitude with increasing relative humidity (RH) from 6 to 95% at room temperature, exhibiting high sensitivity, and that, in the range of 20-95% RH, the Log(Deltaf) showed good linearity. The sensitivity of fibrous composite polyacrylic acid (PAA)/poly(vinyl alcohol) (PVA) membranes was two times higher than that of the corresponding flat films at 95% RH. Compared with fibrous PAA/PVA membranes, the nanofibrous PAA membranes exhibited remarkably enhanced humidity sensitivity due to their high PAA content and large specific surface area caused by the formation of ultrathin nanowebs among electrospun fibers. Additionally, the resultant sensors exhibited a good reversible behavior and good long term stability.
High-Response Room-Temperature NO2 Sensor and Ultrafast Humidity Sensor Based on SnO2 with Rich Oxygen Vacancy.

Yujia Zhong,WeiWei Li,Xuanliang Zhao,Xin Jiang,Shuyuan Lin,Zhen,Wenduo Chen,Dan Xie,Hongwei Zhu

DOI: https://doi.org/10.1021/acsami.9b01737

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:SnO2 nanosheets with abundant vacancies (designated as SnO2- x) have been successfully prepared by annealing SnSe nanosheets in Argon. The transmission electron microscopy results of the prepared SnO2 nanosheets indicated that high-density SnO2- x nanoplates with the size of 5-10 nm were distributed on the surface of amorphous carbon. After annealing, the acquired SnO2- x/amorphous carbon retained the square morphology. The stoichiometric ratio of Sn/O = 1:1.55 confirmed that oxygen vacancies were abundant in SnO2 nanosheets. The prepared SnO2- x exhibited excellent performance of sensing NO2 at room temperature. The response of the SnO2- x-based sensor to 5 ppm NO2 was determined to be 16 with the response time and recovery time of 331 and 1057 s, respectively, which is superior to those of most reported room-temperature NO2 sensors based on SnO2 and other materials. When the humidity varied from 30 to 40%, Δ R/ R was 0.025. The ultrafast humidity response (52 ms) and recovery (140 ms) are competitive compared with other state-of-art humidity sensors. According to the mechanistic study, the excellent sensing performance of SnO2- x is attributed to its special structure.
High-performance Flexible Humidity Sensor Based on B-TiO2/ SnS2 Nanoflowers for Non-Contact Sensing and Respiration Detection

Jingzhe Zhang,Honglie Shen,Yufang Li,Xiang Li,Jiaxin Sun,Di Yan,Xinghan Jin,Xuanhao Wu

DOI: https://doi.org/10.1016/j.surfin.2024.105136

IF: 6.2

2024-01-01

Surfaces and Interfaces

Abstract:The development of flexible humidity sensors is essential for the advancement of wearable devices and electronic skin. However, the process of preparing these sensors is typically complex, and they often suffer from poor stability and a limited sensing range, which fails to meet the requirements for practical applications. Here, we prepared SnS2 with nanoflower morphology by hydrothermal method, and successfully prepared a high-performance flexible humidity sensor with a high response range (20-95%) by compositing it with B-TiO2 nanoparticles with oxygen defects after sodium borohydride reduction and coating it on a PET flexible substrate. This sensor demonstrates an exceptional response (753.2 at 90% RH) in high humidity environments and exhibits rapid response (13 s) and recovery times (19 s). Moreover, the sensor accurately detects human breathing patterns and frequencies, making it suitable for non-contact sensing applications. This research offers valuable insights into the simplified preparation and advancement of flexible humidity sensors.
Highly sensitive humidity sensors based on hexagonal boron nitride nanosheets for contactless sensing

Hang Liu,Jinxu Qin,Xigui Yang,Chaofan Lv,Wentao Huang,Fukui Li,Chuang Zhang,Yanran Wu,Lin Dong,Chongxin Shan

DOI: https://doi.org/10.1007/s12274-023-5837-1

IF: 9.9

2023-06-30

Nano Research

Abstract:Humidity sensors with high sensitivity, rapid response, and facile fabrication process for contactless sensing applications have received considerable attention in recent years. Herein, humidity sensors based on hexagonal boron nitride (h-BN) nanosheets that are synthesized by a facile ultrasonic process have been fabricated, which display an ultrahigh sensitivity of 28,384% at 85% relative humidity (RH), rapid response/recovery time (3.0/5.5 s), and long-term stability in a wide humidity detection range (11%–85% RH), superior to most of the reported humidity sensors. The high sensitivity can be ascribed to the massive hydrophilic functional groups absorbed on the h-BN nanosheet surface. Benefiting from the high humidity sensing performances, contactless Morse code messaging and human writing and speech recognition have been demonstrated. This work demonstrates the great potential of the high-performance h-BN nanosheet-based humidity sensors for future contactless sensing devices.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology

Fast and Highly Sensitive Humidity Sensors Based on NaNbO3 Nanofibers

A RESISTIVE-TYPE NANOSTRUCTURED HUMIDITY SENSOR PREPARED BY ELECTROSPINNING

High-sensitivity fiber-optic humidity sensor based on microfiber overlaid with niobium disulfide

A Fast Humidity Sensor Based on Li+-Doped SnO2 One-Dimensional Porous Nanofibers

Ultrafast Response Humidity Sensor Based on Electrospun Porous BaTiO3 Nanofibers

QCM-based Humidity Sensor and Sensing Properties Employing Colloidal SnO2 Nanowires

Highly Sensitive and Ultrafast Response Surface Acoustic Wave Humidity Sensor Based on Electrospun Polyaniline/poly(vinyl Butyral) Nanofibers.

Facile Fabrication of Nylon66/Multi-Wall Carbon Nanotubes/Polyvinyl Alcohol Nanofiber Bundles for Use as Humidity Sensors

High sensitivity Optical Humidity Sensing Based on Polymer Microfiber Cavity Coupled Metallic Nanorod

Humidity Sensors Using in Situ Synthesized Sodium Polystyrenesulfonate/zno Nanocomposites.

Electrospun nanofibers of polymer composite as a promising humidity sensitive material

Humidity Sensors Based on ZnO/TiO2 Core/shell Nanorod Arrays with Enhanced Sensitivity

High-temperature humidity sensors based on WO3–SnO2 composite hollow nanospheres

A Flexible Humidity Sensor Based on Co3O4 Nanoneedles with High Sensitivity and Quick Response

Graphitic Carbon Nitride Nanosheets Deposited on Microfibers for Relative Humidity Sensing

Ultrafast Self-Assembly MoS2/Cu(OH)2 Nanowires for Highly Sensitive Gamut Humidity Detection with an Enhanced Self-Recovery Ability.

Flexible and Highly Sensitive Humidity Sensor Based on Sandwich-Like Ag/Fe3O4 Nanowires Composite for Multiple Dynamic Monitoring

A highly sensitive humidity sensor based on a nanofibrous membrane coated quartz crystal microbalance

High-Response Room-Temperature NO2 Sensor and Ultrafast Humidity Sensor Based on SnO2 with Rich Oxygen Vacancy.

High-performance Flexible Humidity Sensor Based on B-TiO2/ SnS2 Nanoflowers for Non-Contact Sensing and Respiration Detection

Highly sensitive humidity sensors based on hexagonal boron nitride nanosheets for contactless sensing