Abstract:The combined effects of thermomigration (TM) and electromigration (EM) were investigated in Cu/Sn3.0Ag0.5Cu/Ni solder joints by applying a 5×103A/cm2 DC current to the joints. With a thermal gradient, the Cu atoms and Ni atoms were found to migrate towards the lower temperature side while the Sn atoms were found to migrate towards the higher temperature side. For the solder joint stressed with a 5×103A/cm2 DC current, TM was found to play a dominant effect on the migration of Cu atoms in the solder because the Cu atomic flux in the solder which was induced by EM was smaller than that was induced by TM. The Ni atomic flux in the solder that was induced by TM was smaller than that induced by EM, but it could not be ignored because the values were the same order of magnitude. The Sn atomic flux induced by TM could be ignored due to its smaller magnitude than that induced by EM. The Cu3Sn IMC layer and Cu6Sn5 IMC layer at the Cu/solder interface in the joint with Cu as the anode were thicker than corresponding layers at the Cu/solder interface in the joint with Cu as the cathode. The IMC at the Ni/solder interface of joint with Cu as the anode was the Ni3Sn4 phase while that in the solder joint with Cu as the anode was the (Cu,Ni)6Sn5, and the former was thicker than the latter. EM and TM induced dissolution of the Ni3Sn4 IMC into the solder was found to be the main cause of the formation of voids at the Ni3Sn4/solder interface from a joint that used Cu as the anode. For the solder joint that used Cu as the anode, the Ni3Sn4 IMC layer at the Ni/solder interface was as thick as the Cu-Sn IMC layer at the Cu/solder interface. By contrast, for the solder joint that used Cu as the cathode, the IMC layer at the Ni/solder interface was thinner than that at the Cu/solder interf- - ace.

The Effect of Micro-Structure Evolution in Electromigration on the Reliability of Solder Joints

The Study of the Reliability of Complex Components during the Electromigration Process

Computational Analysis of Mechanical and Electromigration Reliability Problems

The coupling effects of thermal cycling and high current density on Sn58Bi solder joints

An in-situ experimental and simulation study on the electromigration behavior of SAC305 solder joints

Experimental and multiphysics simulation study of atoms migration and morphology evolution in solder joints under high current density

Comparison of the Time-Dependent Physical Processes in the Electromigration of Deep Submicron Copper and Aluminum Interconnects

Investigation of Stress Evolution Induced by Electromigration in Sn-Ag-Cu Solder Joints Based on an X-Ray Diffraction Technique

Investigation on electromigration failure behavior of SAC305/SnPb micro-hybrid solder joints for package-on-package techniques: Experiment and simulation

Counteracting Effect of Sn Grain Orientation on Current Crowding in Electromigration Failures of Solder Joints

Study of electromigration in Sn-Ag-Cu micro solder joint with Ni interfacial layer

The In-Situ Observation of Grain Rotation and Microstructure Evolution Induced by Electromigration in Sn-3.0Ag-0.5Cu Solder Joints

Impact of Mechanical Property Degradation and Intermetallic Compound Formation on Electromigration-Oriented Failure of a Flip-Chip Solder Joint

The microstructure evolution and failure mechanism of Sn37Pb solder joints under the coupling effects of extreme temperature variation and electromigration

Reliability Study of Fine Pitch Cu-Sn Micro-Bump Structure Electromigration Test by Finite Element Simulation

Electromigration and Thermomigration in Sn3Ag0.5Cu Solder Joints

Incorporating Tensile Stress into Electromigration Life Prediction for Cu/SAC305/Cu Solder Joints

Dependence of electromigration caused by different mechanisms on current densities in VLSI interconnects

Current-induced solder evolution and mechanical property of Sn-3.0Ag-0.5Cu solder joints under thermal shock condition

Electromigration Effects Upon Interfacial Reactions

Electromigration in Cu–Cu joints: Measurement of activation energy and polarity effect