In-cell DNA Detection Probe Fabrication Based on Microgap Structure Sensor

Yunmiao Wang,Kristie L Cooper,Anbo Wang

DOI: https://doi.org/10.1364/fio.2008.jwa4

2008-01-01

Abstract:This paper presents a potential method to fabricate a robust in-cell DNA detection probe combining the advantages of pulling and etching technologies. A sensor tip with 10μm diameter has been fabricated.

What problem does this paper attempt to address?

Detection of Single Molecular DNA Charge Through TFT-Integrated Nanopore Biosensor

Xin Zhu,Xiaojie Li,Chaoming Gu,Zhi Ye,Zhen Cao,Yang Liu

DOI: https://doi.org/10.1109/mems51670.2022.9699446

2022-01-01

Abstract:We developed nanopore devices that monolithically integrate thin-film transistors along the inner walls of the nanopores, with the TFT channel lengths and nanopore diameters both reaching ~10 nm. The device is self-aligned and the fabrication process is compatible with the conventional TFT process and TEM drilling process. We demonstrated sensing of the single molecular DNA charge through such devices. Negatively charged dsDNA translocation experiments were conducted. Correlated ionic and TFT signals were identified from the two-channel recording. The charge-based field effect is attributed to the sensing process and is consistent with the device characteristics.
Fabrication of microcoil/microsprings for novel chemical and biological sensing

Yangqing Lu,Hai-Feng Ji

DOI: https://doi.org/10.1016/j.snb.2006.10.058

2007-01-01

Abstract:This paper reports the fabrication of a novel microsensor structure using inductively coupled plasma source (ICP) dry etching process. The novel sensor is based on a SiO2/Si/SU-8 trilayered microcoil/microspring structure. The diameter of the microcoil was approximately 600μm. The ICP process and SU-8 exposing time are discussed. The SiO2 layer can be conveniently modified according to typical silica surface modification procedures. The microcoils could expand or contract upon interaction of specific species in the environment with receptors on the SiO2 surface due to the surface stress or energy applied on the SiO2 surface of the microcoil. This microcoil device may be widely used in biomedical and chemical sensing applications.
Fabrication of Submicron-Gap Electrodes by Silicon Volume Expansion for DNA-detection

Xuejiao Chen,Jian Zhang,Zhiliang Wang,Qiang Yan

DOI: https://doi.org/10.1016/j.sna.2011.12.046

2012-01-01

Abstract:In this paper, submicron-gap electrodes were fabricated by traditional IC technology. The principle involved is based on the silicon volume expansion in the transition from silicon (Si) to silicon dioxide (SiO2) during thermal oxidation. The micron-level silicon electrode gaps were first generated on the silicon wafer by the conventional photolithography followed by deep reactive ion etching process. The thermal oxidation was then conducted to induce silicon volume expansion. As a result, the gap distance can decrease from micron level to submicron or even nanometer level, which depends on the oxidation parameters. Subsequently, the electrical DNA sensor, which can detect the I–V variations during DNA hybridization, had been constructed with the interdigitated submicron-gap electrodes. The result shows that the sensitivity of as-fabricated electrodes with 600nm gap width can reach 2.5μA/nM. This method may enable the batch-production and low-cost DNA biosensors.
Mass-Produced Nanogap Sensor Arrays for Ultrasensitive Detection of DNA

Somenath Roy,Xiaojun Chen,Mo‐Huang Li,Yanfen Peng,Franklin Anariba,Zhiqiang Gao

DOI: https://doi.org/10.1021/ja901704t

IF: 15

2009-01-01

Journal of the American Chemical Society

Abstract:In this report, an electrical detection scheme for the quantification of DNA using a nanogap sensor array is detailed. The prime objective is to develop a novel sensing procedure, based on the electronic transduction mechanism, which would mitigate the problems intrinsic to nanostructure-based biosensing devices. Design considerations of the sensor array take into account the feasibility of mass production in a cost-effective way by using standard silicon microfabrication technologies. The sensing mechanism relies on bridging the nanogap upon hybridization of the two termini of a target DNA with two different surface-bound capture probes, followed by a simple metallization step. About 2 orders of magnitude enhancement in conductance, as referred to a clean background (<1.0 pS) observed at a control sensor, was obtained in the presence of as little as 1.0 fM target DNA. This sensitivity is comparable to the best of electrochemical/electrical biosensors. A linear relationship between the conductance and the DNA concentration was obtained from 1.0 fM to 1.0 pM with an exceptional signal intensity of 2.1 x 10(4)% change per unit concentration. This change in conductivity is so large that it can unambiguously detect the concentration of DNA quantitatively and may obviate the need for target amplification used in current DNA tests. Moreover, the sensor array exhibited excellent single-base mismatch discrimination due to its unique vertically aligned nanostructure and the two-probe configuration.
Microgap Structured Optical Sensor for Fast Label-Free DNA Detection

Yunmiao Wang,Kristie L. Cooper,Anbo Wang

DOI: https://doi.org/10.1109/jlt.2008.926924

IF: 4.7

2008-01-01

Journal of Lightwave Technology

Abstract:This paper presents a new label-free DNA optical sensor based on the microgap structured Fabry-Perot interferometer. An optical cavity is formed by a microgap sealed between a singlemode fiber and a well-cleaved fiber end. The capture DNA is immobilized on the cavity end by layer-by-layer electrostatic self-assembly. This sensor detects the hybridization of target DNA with complementary capture DNA by observing the optical cavity thickness variation. Experimental results demonstrate that this sensor has a sensitivity of 6 nmol/ml and can identify a 2-bp mismatch.
Single End Microfiber Biosensor for DNA Hybridization Detection.

Yanpeng Li,Fang,Shijie Tan,Liuyang Yang,Qizhen Sun

DOI: https://doi.org/10.23919/ps.2019.8817817

2019-01-01

Abstract:We report a single end microfiber probe with compact size, which is simply fabricated by snapping a biconical microfiber. Its application in DNA hybridization detection is also presented.
Electric Detection of Dna with Pdms Microgap Electrodes and Silver Nanoparticles

Ziyin Sun,Weibing Qiang,Hui Li,Nan Hao,Danke Xu,Hong-Yuan Chen

DOI: https://doi.org/10.1039/c0an00512f

2011-01-01

Abstract:In this work a novel microdevice sensor has been developed by plating gold on the PDMS surface to generate a sandwich-type gap electrode for DNA detection. The microdevice utilizes a gold band electrode-PDMS-gold band electrode configuration and the minimum detectable volume could be as low as 5 μL. The 20 μm PDMS-based gap was chemically modified with DNA capture probes and DNA sandwich hybrids were formed with the addition of DNA target and silver nanoparticle probes. To increase detection sensitivity, parallel detection zones have been developed in which the relevant resistances decrease substantially upon hybridyzation. By measuring the change in electrical conductivity, the DNA target in the concentration range of 1000-0.1 nM can be assayed and the limit of lowest detectable concentration was achieved at 0.01 nM.
Design and Fabrication of a 3-D Nanogap Electrode Grid Array Biosensor

Yonghong Liu,Zhan Zhao

DOI: https://doi.org/10.1109/nems.2007.352127

2007-01-01

Abstract:With the development of biotechnology and nanotechnology, a kind of 3-D nanogap electrode grid array biosensor is designed based on dielectrophoresis, impedance method and NEMS technology. This chip is expected to separate and detect cells label freely by electrical method. Researches are mainly done about the most important problem on fabrication of the biosensor and a new technology is developed. The sidewall etching of RIE is used to form thin nanogap metal cantilevers which configurate the 3-D nanogap electrode grid array structure. Anisotropy of RIE is modeled and the etching profiles are simulated. This method is proved to be applicable by analysis and experiments.
In Situ Terminus-Regulated DNA Hydrogelation for Ultrasensitive On-Chip Microrna Assay.

Shengyuan Deng,Juan Yan,Fei Wang,Yan Su,Xueli Zhang,Qian Li,Guang Liu,Chunhai Fan,Hao Pei,Ying Wan

DOI: https://doi.org/10.1016/j.bios.2019.04.053

IF: 12.545

2019-01-01

Biosensors and Bioelectronics

Abstract:In this work, a dynamic terminus-regulated fabric of DNA hydrogel was invented in debt to the reiterative catalysis of terminal deoxynucleotidyl transferase (TdT). It extended free 3' - OH end to an overhang of homopolymeric adenosine base pair, and alternated with branching from the frayed complementary seed oligo T(20)G(5). The cycle of this template-independent and isothermal amplification resulted in a microscale dendritic DNA fractal at first, which then gelatinized into a cohesive and intricate 3D network. Details of the complex were elucidated with gel electrophoresis, confocal and atomic force microscopy. Its well hydrated inner space could further provide plenty of biocompatible chambers for enzymatic transducers fused along the elongation. Taking merits of this neat and flexible setup, an in situ hydrogelation strategy was developed and utilized in the signal cascade of a miRNA biomarker detector on an electrode microarray, thus accomplished an ultrasensitive, selective and high-throughput sensing even for real samples. This collective manipulation of DNA-protein hydrogel ensemble on interface demonstrates its potency as a general scheme of sensitization in bioanalytical applications.
Sensitive and Selective DNA Detection Based on the Combination of Hairpin-Type Probe with Endonuclease/gnp Signal Amplification Using Quartz-Crystal-microbalance Transduction.

Yuehua Fei,Xiao-Yong Jin,Zai-Sheng Wu,Song-Bai Zhang,Guoli Shen,Ru-Qin Yu

DOI: https://doi.org/10.1016/j.aca.2011.02.040

IF: 6.911

2011-01-01

Analytica Chimica Acta

Abstract:In order to develop a highly sensitive and selective piezoelectric transducer for the detection of DNA, the bio-recognizing probe is for the first time designed by introducing a hairpin structure and a recognition site for EcoRI into an oligonucleotide sequence and signal amplifiers are prepared by modifying gold nanoparticles (GNPs) with biomolecules, deepening the application and understanding of biomaterials. The piezoelectric transducer is prepared by immobilizing designed hairpin recognition probe onto the quartz-crystal-microbalance (QCM). In the absence of target DNA, the hairpin probe is removed from the QCM surface after exposure to endonuclease, inhibiting the subsequent signaling reaction. In contrast, introduction of target DNA can open the hairpin probe due to the probe/target hybridization, dissociating the cleavable double-stranded portion. In this case, even if being treated with endonuclease, the integrated hairpin probe is maintained. Subsequent introduction of GNPs modified with detection probes that can hybridize to the terminal sequence of hairpin probe results in a many-folds increase of the frequency response. Utilizing the proposed transduction scheme, the reliable target DNA detection can be accomplished. The detection limit of 2 pM and dynamic response range for target DNA from 2 to 300 pM are obtained. Furthermore, single-base mismatched DNAs can be easily identified. The developed proof-of-principle of a novel piezoelectric transduction scheme is expected to establish a potential platform for the disease-associated mutation analysis and DNA hybridization detection in biotechnology and medical diagnostics.
Controllable Fabrication of Sub-10 nm Graphene Nanopores via Helium Ion Microscopy and DNA Detection

Zhishan Yuan,Yanbang Lin,Jieming Hu,Chengyong Wang

DOI: https://doi.org/10.3390/bios14040158

2024-03-28

Biosensors

Abstract:Solid-state nanopores have become a prominent tool in the field of single-molecule detection. Conventional solid-state nanopores are thick, which affects the spatial resolution of the detection results. Graphene is the thinnest 2D material and has the highest spatial detection resolution. In this study, a graphene membrane chip was fabricated by combining a MEMS process with a 2D material wet transfer process. Raman spectroscopy was used to assess the quality of graphene after the transfer. The mechanism behind the influence of the processing dose and residence time of the helium ion beam on the processed pore size was investigated. Subsequently, graphene nanopores with diameters less than 10 nm were fabricated via helium ion microscopy. DNA was detected using a 5.8 nm graphene nanopore chip, and the appearance of double-peak signals on the surface of 20 mer DNA was successfully detected. These results serve as a valuable reference for nanopore fabrication using 2D material for DNA analysis.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation
Detection of Sub-fM DNA with Target Recycling and Self-Assembly Amplification on Graphene Field-Effect Biosensors.

Zhaoli Gao,Han Xia,Jonathan Zauberman,Maurizio Tomaiuolo,Jinglei Ping,Qicheng Zhang,Pedro Ducos,Huacheng Ye,Sheng Wang,Xinping Yang,Fahmida Lubna,Zhengtang Luo,Li Ren,Alan T. Charlie Johnson

DOI: https://doi.org/10.1021/acs.nanolett.8b00572

IF: 10.8

2018-01-01

Nano Letters

Abstract:All-electronic DNA biosensors based on graphene field-effect transistors (GFETs) offer the prospect of simple and cost-effective diagnostics. For GFET sensors based on complementary probe DNA, the sensitivity is limited by the binding affinity of the target oligonucleotide, in the nM range for 20 mer targets. We report a similar to 20 000x improvement in sensitivity through the use of engineered hairpin probe DNA that allows for target recycling and hybridization chain reaction. This enables detection of 21 mer target DNA at sub-fM concentration and provides superior specificity against single-base mismatched oligomers. The work is based on a scalable fabrication process for biosensor arrays that is suitable for multiplexed detection. This approach overcomes the binding-affinity-dependent sensitivity of nucleic acid biosensors and offers a pathway toward multiplexed and label-free nucleic acid testing with high accuracy and selectivity.
Monolithic Fabrication of NPN/SiNx Dual Membrane Cavity for Nanopore-based DNA Sensing

Gregory R Madejski,Kyle Briggs,Jon-Paul DesOrmeaux,Joshua J Miller,James A Roussie,Vincent Tabard-Cossa,James L McGrath

DOI: https://doi.org/10.1002/admi.201900684

2019-07-23

Abstract:Nanoscale preconfinement of DNA has been shown to reduce the variation of passage times through solid-state nanopores. Preconfinement has been previously achieved by forming a femtoliter-sized cavity capped with a highly porous layer of nanoporous silicon nitride (NPN). This cavity was formed by sealing a NPN nanofilter membrane against a substrate chip using water vapor delamination. Ultimately, this method of fabrication cannot keep a consistent spacing between the filter and solid-state nanopore due to thermal fluctuations and wrinkles in the membrane, nor can it be fabricated on thousands of individual devices reliably. To overcome these issues, we present a method to fabricate the femtoliter cavity monolithically, using a selective XeF2 etch to hollow out a polysilicon spacer sandwiched between silicon nitride layers. These monolithically fabricated cavities behave identically to their counterparts formed by vapor delamination, exhibiting similar translocation passage time variation reduction and folding suppression of DNA without requiring extensive manual assembly. The ability to form nanocavity sensors with nanometer-scale precision and to reliably manufacture them at scale using batch wafer processing techniques will find numerous applications, including motion control of polymers for single-molecule detection applications, filtering of dirty samples prior to nanopore detection, and simple fabrication of single-molecule nanobioreactors.
Fabrication of Graphene Nanopores and a Preliminary Study on Λ-Dna Translocation

Wang Yue,Yu Xufeng,Liu Yunyun,Xie Xiao,Cheng Xiulan,Huang Shaoming,Wang Zhimin

DOI: https://doi.org/10.6023/a13121208

2014-01-01

Abstract:Nanopore sequencing is among the most promising technologies to achieve the goals of the "$1,000 Genome." Two major types of nanopores have been extensively investigated, protein and silicon-based solid-state nanopores. However, protein pores are short-lived and the length of solid-state nanopores is much larger than the distance between adjacent bases, resulting in incapability to discriminate individual bases along the single-stranded DNA molecules. In this paper, we report lambda-DNA translocations through graphene nanopore. A large nanopore with diameter of about 30 nm on silicon nitride substrates were first fabricated using focused ion beam (FIB) system under the beam current of 2 pA, accelerating voltage of 30 kV and sculpting time of 1 s. Individual graphene membranes were suspended onto the substrates to cover the large pore, and nanopores with a diameter less than 10 am are sculpted in the graphene sheet by focused electron beam (FEB) from a transmission electron microscope (TEM) under a 400 kx magnification times and 300 kV accelerating voltage at 1 x 10(5)similar to 5 x 10(5) A/m(2) current density for 2 similar to 3 min The edges of these graphene nanopores became smoother and sharper when the temperature was increased to about 450 degrees C, which might help to lower interactions between graphene nanopores and the analytes. The signals of DNA translocation through graphene nanopores had been recorded using a patch clamp amplifier at 10 kHz sampling frequency filtered at 5 kHz via an integrated four-pole low-pass Bessel filter. Analyses of the DNA translocation current traces indicated that different conformations of DNA molecules may exist during entrance into nanopores. In addition, our overall detection platform had a low noise amplitude of around 10 pA, which allowed more sensitive signal detection. Taken together, our observations demonstrate that graphene nanopores are feasible for DNA sensing, leading a forward step towards single-molecule DNA sequencing using monolayered graphene nanopores.
Wafer-lever Au Nanogap-Nanopore Fabricated by NEMS Technology

Zhishan Yuan,Yunfei Chen,Zhonghua Ni,Hong Yi,Yuelin Wang,Tie Li

DOI: https://doi.org/10.1142/9789814719391_0045

2015-01-01

Abstract:Nowadays, nanogap-nanopore devices have attracted widely concerns for its potential application in the third generation DNA sequencing. However, an effective universal method to fabricate nanogap-nanopore device is still needed to overcome the low efficiency problem in fabrication technology. In this paper, wafer-lever Au nanogap-nanopore was fabricated by NEMS technology successfully. Suspended sandwich structure (SiN-Au nanowire-SiO2, 100nm/20nm/200nm thick) was demonstrated, which can isolate Au nanowire and salt solution effectively. Moreover, this thin nano structure made Au nanogap-nanopore milling much easier with the help of focused ion beam (FIB) in a controllable way. Since the whole manufacture process was achieved in wafer-lever, this method made Au nanogap-nanopore in DNA sequencing more convenient.
Nanopore arrays in a silicon membrane for parallel single-molecule detection: fabrication

Torsten Schmidt,Miao Zhang,Ilya Sychugov,Niclas Roxhed,Jan Linnros

DOI: https://doi.org/10.1088/0957-4484/26/31/314001

IF: 3.5

2015-07-16

Nanotechnology

Abstract:Solid state nanopores enable translocation and detection of single bio-molecules such as DNA in buffer solutions. Here, sub-10 nm nanopore arrays in silicon membranes were fabricated by using electron-beam lithography to define etch pits and by using a subsequent electrochemical etching step. This approach effectively decouples positioning of the pores and the control of their size, where the pore size essentially results from the anodizing current and time in the etching cell. Nanopores with diameters as small as 7 nm, fully penetrating 300 nm thick membranes, were obtained. The presented fabrication scheme to form large arrays of nanopores is attractive for parallel bio-molecule sensing and DNA sequencing using optical techniques. In particular the signal-to-noise ratio is improved compared to other alternatives such as nitride membranes suffering from a high-luminescence background.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Nanosphere Lithography for Sub-10-Nm Nanogap Electrodes

Deyang Ji,Tao Li,Harald Fuchs

DOI: https://doi.org/10.1002/aelm.201600348

IF: 6.2

2017-01-01

Advanced Electronic Materials

Abstract:Nanogap electrodes are effective tools for probing and detection of single molecules in the field of molecular electronics. By using nanosphere lithography, an innovative approach to prepare sub-10-nm nanogap electrodes is introduced. More significantly, nanogap arrays are also obtained in a reproducible and cost-efficient way. As an application, DNA molecules are assembled into the nanogaps for electrical detection.
DNA Sensors: A DNA Nanostructure-based Biomolecular Probe Carrier Platform for Electrochemical Biosensing (Adv. Mater. 42/2010)

Hao Pei,Na Lu,Yanli Wen,Shiping Song,Yan Liu,Hao Yan,Chunhai Fan

DOI: https://doi.org/10.1002/adma.201090136

IF: 29.4

2010-01-01

Advanced Materials

Abstract:A 3D DNA nanostructure-based sensor platform for DNA detection is presented by Chunhai Fan, Hao Yan, and co-workers on p. 4754. The strategy provides significantly enhanced spatial positioning range and accessibility for probes on a surface over previously reported DNA-sensing architectures. Use of this versatile detection platform leads to highly sensitive and selective DNA detection in biological fluids and greatly enhanced sequence specificity for SNP typing.
Impedance Sensing of DNA Immobilization and Hybridization by Microfabricated Alumina Nanopore Membranes

Songmei Wu,WeiWei Ye,Mo Yang,Mojtaba Taghipoor,Robert Meissner,Juergen Brugger,Philippe Renaud

DOI: https://doi.org/10.1016/j.snb.2015.03.094

IF: 9.221

2015-01-01

Sensors and Actuators B Chemical

Abstract:In this work we demonstrate microfabricated thin alumina nanopore membranes as a platform for impedance sensing of DNA immobilization and hybridization. We develop a wafer-scale fabrication of free-standing alumina nanopore membranes with well controlled thickness, pore diameter and overall pore density. One 1cm×1cm single chip contains an array of 69 membranes. Each membrane is 100μm×100μm large and 2μm thick, with pore diameter of 120nm. With low pore density of ∼6pores/μm2, nanopore resistance and membrane capacitance can be recognized clearly in the electrochemical impedance spectrum from 100 to 1MHz. The total surface area can be further increased by the coating of silica nanoparticles with ∼20nm in diameter. During the immobilization of probe ssDNA to (3-glycidoxypropyl) trimethoxysilane functionalized surface, the nanopore resistance drops significantly by 80%, whereas the membrane capacitance increases less than 2%. After hybridization with complementary DNA, the nanopore resistance increases up to 10%. Non-complementary ssDNA has no obvious effect. The detection limit is 12.5nM in phosphate-buffered saline (PBS) solution.
In-situ DNA Hybridization Detection Based on a Reflective Microfiber Probe

Yanpeng Li,Fang,Liuyang Yang,ShiJie Tan,Zhijun Yan,Qizhen Sun

DOI: https://doi.org/10.1364/oe.380896

IF: 3.8

2019-01-01

Optics Express

Abstract:A label-free biosensor based on a reflective microfiber probe for in-situ real-time DNA hybridization detection is proposed and experimentally demonstrated. The microfiber probe is simply fabricated by snapping a non-adiabatic biconical microfiber through closing the oxyhydrogen flame during fiber stretching. Assisted with the Fresnel reflection at the end of microfiber, a reflective microfiber modal interferometer is realized. The in-situ DNA hybridization relies on the surface functionalization of a monolayer of Poly-L-lysine (PLL) and synthetic DNA sequences that bind to a given target with high specificity. The detection processes of DNA hybridization in various concentration of target DNA solutions are monitored in real-time and the experimental results present a minimum detectable concentration of 10pM with good repeatability. Additionally, the detection specificity is also investigated by immersing the microfiber probe into the non-complementary ssDNA solutions and observing the spectral variation. The proposed biosensor has advantages of high sensitivity, compact size, ease of use and simple fabrication, which makes it has great potential to be applied in a lot of fields such as disease diagnosis, medicine, and environmental science.

In-cell DNA Detection Probe Fabrication Based on Microgap Structure Sensor

Detection of Single Molecular DNA Charge Through TFT-Integrated Nanopore Biosensor

Fabrication of microcoil/microsprings for novel chemical and biological sensing

Fabrication of Submicron-Gap Electrodes by Silicon Volume Expansion for DNA-detection

Mass-Produced Nanogap Sensor Arrays for Ultrasensitive Detection of DNA

Microgap Structured Optical Sensor for Fast Label-Free DNA Detection

Single End Microfiber Biosensor for DNA Hybridization Detection.

Electric Detection of Dna with Pdms Microgap Electrodes and Silver Nanoparticles

Design and Fabrication of a 3-D Nanogap Electrode Grid Array Biosensor

In Situ Terminus-Regulated DNA Hydrogelation for Ultrasensitive On-Chip Microrna Assay.

Sensitive and Selective DNA Detection Based on the Combination of Hairpin-Type Probe with Endonuclease/gnp Signal Amplification Using Quartz-Crystal-microbalance Transduction.

Controllable Fabrication of Sub-10 nm Graphene Nanopores via Helium Ion Microscopy and DNA Detection

Detection of Sub-fM DNA with Target Recycling and Self-Assembly Amplification on Graphene Field-Effect Biosensors.

Monolithic Fabrication of NPN/SiNx Dual Membrane Cavity for Nanopore-based DNA Sensing

Fabrication of Graphene Nanopores and a Preliminary Study on Λ-Dna Translocation

Wafer-lever Au Nanogap-Nanopore Fabricated by NEMS Technology

Nanopore arrays in a silicon membrane for parallel single-molecule detection: fabrication

Nanosphere Lithography for Sub-10-Nm Nanogap Electrodes

DNA Sensors: A DNA Nanostructure-based Biomolecular Probe Carrier Platform for Electrochemical Biosensing (Adv. Mater. 42/2010)

Impedance Sensing of DNA Immobilization and Hybridization by Microfabricated Alumina Nanopore Membranes

In-situ DNA Hybridization Detection Based on a Reflective Microfiber Probe