Abstract:Cold crucible induction melter (CCIM) technology has been widely used in melting of non-metallic refractory materials with a high melting point and a requirement of high purity. This paper discusses the application of the CCIM technology in melting of reactor corium (simulated as zirconium oxide in this experiment).In this experiment, the power supply is set at constant power control mode, with a design frequency of similar to 100 kHz and a total output power of similar to 400 kW. The cold crucible consists of copper tubes and a stainless bottom plate which has a dimension of 220 mm in diameter and 420 mm in height. The crucible is charged with zirconium oxide (ZrO2) powder and surrounded by a set of water-cooling induction coils which is designed shorter than the crucible in order to reduce energy loss in the water-cooling bottom plate. The top of the crucible and the coils are at the same height. A Zirconium ring is used to initiate heating process. similar to 50 kg ZrO2 powder is used for each experiment. Electrical variables of the induction melter and temperature of the melt are detected and recorded in the entire heating process.For the result, almost 3/4 of the ZrO2 powder is melt and a thin crust (2-3 mm) is generated between the melt and the crucible. To be specific, the ZrO2 powder above the bottom of the induction coils is melt, but others are not. In the melting process, the maximum surface temperature of the melt has reached 2230 t. Furthermore, for better understanding of the relationship between the melting process and the changing process of the electrical variables, an equivalent circuit of the heating system is established and analyzed. It can be concluded that some electrical variables such as the quality factor (Q) of the induction coils and the practical frequency can reflect melting status. The conclusion is confirmed by the records transmitted by sensors in the melting process. By comparison between the recorded data and the melting status, it is clear that the Q value can be accurately used in indicating the melting status due to its obvious change in the entire melting process. As the melting pool becoming larger, the Q value tends to be smaller. In contrast, the practical frequency becomes higher as the melt becoming larger. Furthermore, both of them are not influenced by the output power. In addition, the output current and the output voltage also can be used to describe the melting status. In specific, a larger melting pool corresponds to a lower output current and a higher output voltage.

Corrosion effects of MIx on ceramic arc tubes of metal halide lamps

Research on the Photometry and Corrosion Characteristics of Rare Earth Iodides in Ceramic Metal Halide Lamps

Review on the Inner Wall Corrosion in Arc Tube of Ceramic Metal Halide Lamp

Research and Development of Low Wattage Ceramic Metal Halide Lamps

Recent Progress in the Technology of Ceramic Metal Halide Lamps

Progresses in Research on Ceramic Metal Halide Lamps

Review on High Temperature Corrosion of Flue Gas from MSW Incineration

Research on the Dimming Characteristics of Small and Medium Wattage Ceramic Metal Halide Lamps

Dimming properties of medium and small wattage ceramic metal halide lamps

Glass-ceramic Phosphors for Solid State Lighting: A Review

Corrosiveness of CMAS and CMAS + salt (NaVO3, Na2SO4 and NaCl) to YSZ thermal barrier coating materials

Preparation of CMAS, LZS glass-ceramics and study of the glass ceramics anti-corrosion properties in liquid leadbismuth eutectic at 500°C

Elaboration and Chemical Corrosion Resistance of Tubular Macro-Porous Cordierite Ceramic Membrane Supports

Effect of Li+ on Luminescence Properties and Thermal Stability of Glass Ceramics Containing SrMoO4

Investigation on the relation of microstructures and CMAS corrosion resistance of high entropy RE disilicates

Experimental Study Of Performance Of Cold Crucible Induction Melter In Melting Corium Simulant

Corrosion evaluation and resistance study of alloys in chloride salts for concentrating solar power plants

Comparison of corrosion behaviors of Sc2O3-CeO2 co-stabilized ZrO2 and YSZ ceramics exposed to CMAS at 1250°C

Deterioration of alkali-activated and Portland cement-based mortars under sulfur oxidizing bacteria corrosion

Comparison of NaVO3+CMAS mixture and CMAS corrosion to thermal barrier coatings

Study of Corrosion Resistance and Degradation Mechanisms in LiTiO2-Li2TiO3 Ceramic