Abstract:Although the mark of 18 power conversion efficiency (PCE) was surpassed recently, organic solar cells (OSCs) still have several challenges to overcome in order to fully compete with silicon-based solar cells in the energy market. One of the main challenges is the upscaling of the technology. Despite the recent advances in PCEs, a big scalability gap still exists between the best lab-scale device and large-scale modules fabricated via roll-to-roll processing. The polymer donor PffBT4T-C9C13 has already shown efficiencies of almost 12 together with PCBM. Combined with the nonfullerene acceptor O-IDTBR, a reduced voltage loss of 0.5 V between the optical band gap and VOC is obtained, with an open-circuit voltage up to 1.12 V, which is one of the highest values reported for OSCs. In this work, we demonstrate a route to upscaling OSCs based on PffBT4T-C9C13:O-IDTBR through temperature-controlled slot-die coating, solving the challenges of the temperature dependent aggregation behavior, which strongly affects the efficiency of the device. Efficiencies above 4 were achieved in our flexible and roll-processed devices with an area of 1 cm2 and the different origins of the scalability lag were studied. As an additional necessary step for scalability, we incorporate the use of a hydrocarbon-based solvent to remove the environmentally dangerous halogenated solvents. To the best of our knowledge, this is the first work reporting PffBT4T:O-IDTBR solar cells fabricated in open air using slot-die coating in a roll-platform with flexible substrates, that mimics large-scale roll-to-roll processing.

Roll-Coated Fabrication of Fullerene-Free Organic Solar Cells with Improved Stability

Roll-Coating Fabrication of Ito-Free Flexible Solar Cells Based on A Non-Fullerene Small Molecule Acceptor

Roll Coated Large Area ITO- and Vacuum-Free All Organic Solar Cells from Diketopyrrolopyrrole Based Non-Fullerene Acceptors with Molecular Geometry Effects

Roll-Coating Fabrication of Flexible Organic Solar Cells: Comparison of Fullerene and Fullerene-Free Systems

Roll-coating Fabrication of Flexible Large Area Small Molecule Solar Cells with Power Conversion Efficiency Exceeding 1%

Printed Light-Trapping Nanorelief Cu Electrodes for Full-Solution-Processed Flexible Organic Solar Cells

Ambient Roll-To-Roll Fabrication of Flexible Solar Cells Based on Small Molecules

Solvent-resistant Small Molecule Solar Cells by Roll-to-roll Fabrication Via Introduction of Azide Cross-Linkable Group

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Enhancing Long‐Term Thermal Stability of Non‐Fullerene Organic Solar Cells Using Self‐Assembly Amphiphilic Dendritic Block Copolymer Interlayers

Printing fabrication of large-area non-fullerene organic solar cells

Environmentally Friendly and Roll-Processed Flexible Organic Solar Cells Based on PM6:Y6

Constraining the Excessive Aggregation of Non-Fullerene Acceptor Molecules Enables Organic Solar Modules with the Efficiency >16

Simultaneous Improvement of Efficiency and Stability of Organic Photovoltaic Cells by using a Cross‐Linkable Fullerene Derivative

Efficient Fullerene-Free Organic Solar Cells Based On Fused-Ring Oligomer Molecules

Enabling Roll-Processed and Flexible Organic Solar Cells Based On PffBT4T Through Temperature-Controlled Slot-Die Coating

Roll‐to‐Roll Printed Large‐Area All‐Polymer Solar Cells with 5% Efficiency Based on a Low Crystallinity Conjugated Polymer Blend

Fully Roll-to-Roll Processed Efficient Perovskite Solar Cells via Precise Control on the Morphology of PbI2:CsI Layer

Achieving 20.8% Organic Solar Cells Via Additive-Assisted Layer-by-layer Fabrication with Bulk P-I-n Structure and Improved Optical Management

Blade-coated efficient and stable large-area organic solar cells with optimized additive

Integrated Molecular, Interfacial, and Device Engineering Towards High-Performance Non-Fullerene Based Organic Solar Cells.