Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Integrated Molecular, Interfacial, and Device Engineering Towards High-Performance Non-Fullerene Based Organic Solar Cells.

Rational Design Non-Fullerene Acceptor-Based High Efficiency BHJ Polymer Solar Cells Through Theoretical Investigations

High-Performance Fullerene-Free Polymer Solar Cells Featuring Efficient Photocurrent Generation from Dual Pathways and Low Nonradiative Recombination Loss

High-Performance Non-fullerene organic solar cells enabled by noncovalent Conformational locks and Side-Chain engineering

Efficient Ternary Organic Solar Cells Enabled by the Integration of Nonfullerene and Fullerene Acceptors with a Broad Composition Tolerance

High‐Efficiency Organic Solar Cells with Wide Toleration of Active Layer Thickness

An Unfused‐Core‐Based Nonfullerene Acceptor Enables High‐Efficiency Organic Solar Cells with Excellent Morphological Stability at High Temperatures

Synthesis of non-fullerene acceptors for highly efficient and thermally stable organic solar cells (Conference Presentation)

Unveiling Excitonic Dynamics in High-Efficiency Nonfullerene Organic Solar Cells to Direct Morphological Optimization for Suppressing Charge Recombination.

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Conjugated Extension of Non-Fullerene Acceptors Enables Efficient Organic Solar Cells with Optoelectronic Response over 1000 nm

Synergistic Control of Multilength-Scale Morphology and Vertical Phase Separation for High-Efficiency Organic Solar Cells

Printable and Large‐Area Organic Solar Cells Enabled by a Ternary Pseudo‐Planar Heterojunction Strategy

Achieving Efficient Organic Solar Cells and Broadband Photodetectors Via Simple Compositional Tuning of Ternary Blends

Non-Halogenated Solvents Processed Efficient ITO-Free Flexible Organic Solar Cells with Upscaled Area

Optimizing the Alkyl Side-Chain Design of a Wide Band-Gap Polymer Donor for Attaining Nonfullerene Organic Solar Cells with High Efficiency Using a Nonhalogenated Solvent

Enhancement Of Intra- And Inter-Molecular Pi-Conjugated Effects For A Non-Fullerene Acceptor To Achieve High-Efficiency Organic Solar Cells With An Extended Photoresponse Range And Optimized Morphology

Computational Chemistry-Assisted Design of a Non-Fullerene Acceptor Enables 17.4% Efficiency in High-Boiling-point Solvent Processed Binary Organic Solar Cells

Towards High-Efficiency Non-Fullerene Organic Solar Cells: Matching Small Molecule/polymer Donor/acceptor

High‐Efficiency Organic Solar Cells Enabled by Chalcogen Containing Branched Chain Engineering: Balancing Short‐Circuit Current and Open‐Circuit Voltage, Enhancing Fill Factor

Single-Component Non-halogen Solvent-Processed High-Performance Organic Solar Cell Module with Efficiency over 14%