Abstract:In this paper, we present a detailed experimental and numerical study of the flow phenomena and the heat transfer in swirl tubes with one and multiple tangential inlet jets. Such tangential jets induce a highly 3D swirling flow and an enhanced turbulence in the tube, increasing the convective heat transfer. Thus, a swirl tube is considered as an effective cooling method for technical applications with high thermal loaded components like gas turbine blades. The flow field, the heat transfer and the pressure loss are examined in a swirl tube with three different inlet jet configurations with one (MI1), three (MI3) or five (MI5) tangential inlet jets in axial direction. For this purpose, we measured the flow field via stereo-PIV (Particle Image Velocimetry) and the heat transfer by applying a transient technique using thermochromic liquid crystals for several Reynolds numbers. The numerical simulations are performed via Detached Eddy Simulation. The PIV results reveal a complex axial velocity changing after each inlet due to the additional mass flow. Two main structures occur in the swirl tube with five inlet jets: a vortex in the tube center in a wave-like form and large spiral vortices around the tube axis especially near the inlet jets. In the inlet region(s) the highest heat transfer occurs and decreases continuously until the next inlet or towards the tube outlet for the swirl tube with one inlet. The swirl tubes with multiple inlets show lower maximum heat transfer rates compared to the swirl tube with only one inlet due to lower inlet jet velocities. However, the heat transfer distribution is more homogeneous over the entire tube length at a much lower pressure loss. The homogeneous heat transfer can be explained by two mechanisms. At the inlets, the tangential jets impinge onto the concave wall and cause an enhanced convective heat transfer correlating with large spiral vortices. Secondly, the axial velocity becomes stronger further downstream after each inlet jet and causes an enhanced heat transfer between the inlet jets. The thermal performance parameter for all investigated swirl tube configurations is in the same order of magnitude. Thus, all swirl tube configurations are suitable for cooling. If one is interested in a maximum heat transfer paid by a high pressure loss, the swirl tube with one inlet is the best choice. If a lower but more homogeneous heat transfer with a low pressure loss is desired, one should choose the swirl tube with multiple inlets.

Heat Transfer Characteristics of Subcooled Flowing Boiling in Circular Tubes with and Without Swirl Tapes under High Heat Fluxes

Subcooled Flow Boiling Heat Transfer of Water in Circular Tubes with Twisted-Tape Inserts under High Heat Fluxes

Heat Transfer Characteristics of Subcooled Water in Circular Tubes With Twist Tapes Insert Under One-side Heating Conditions

Critical Heat Flux of Highly Subcooled Water Flow Boiling in Circular Tubes with and Without Internal Twisted Tapes under High Mass Fluxes

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Study of the Natural Circulation Flow Boiling Heat Transfer Based On Partially Superhydrophilic Surface Modification

Experimental Design and Analysis for Film Boiling Heat Transfer in a Circular Tube

Numerical Simulation in A Subcooled Water Flow Boiling for One-Sided High Heat Flux in Reactor Divertor

Flow and Heat Transfer Measurements in Swirl Tubes with One and Multiple Tangential Inlet Jets for Internal Gas Turbine Blade Cooling

Flow boiling heat transfer in a vertical spirally internally ribbed tube

An investigation on heat transfer to water flowing in vertical upward internally ribbed enhancement tube at supercritical pressure

Flow Boiling in Inner Annulus of Horizontal Enhanced Tubes

Study On Heat Transfer Of High-Pressure Steam-Water Two-Phase Mixture In Helical Coils

Numerical study on heat transfer characteris tics of supercritical water in straight and helical tubes

Experimental Investigation of Subcooled Flow Boiling Characteristics of Water in Vertical Helically Coiled Tubes

Heat transfer enhancement of helical tubes during pool boiling

Study of Flow Boiling Heat Transfer in A Tube with Axial Microgrooves

Numerical Simulation on Heterogeneous Heat Transfer in Water at Supercritical Pressures in Inclined Upward Tubes

A Numerical Study on Subcooled Flow Boiling Heat Transfer in Tubes with Various Helical Angles at Underwater Vehicles Conditions

Experimental study on friction pressure drop and circumferential heat transfer characteristics in helical tubes

Flow boiling heat transfer characteristics in vertical upward internally ribbed tube