Abstract:The divertor first wall and neutral beam injection (NBI) components of tokamak devices require high heat flux removal up to 20–30 MW m−2 for future fusion reactors. The water cooled HyperVapotron (HV) structure, which relies on internal grooves or fins and boiling heat transfer to maximize the heat transfer capability, is the most promising candidate. The HV devices, that are able to transfer large amounts of heat (1–20 MW m−2) efficiently, have therefore been developed specifically for this application. Until recently, there have been few attempts to observe the detailed bubble characteristics and vortex evolvement of coolant flowing inside their various parts and understand of the internal two-phase complex heat transfer mechanism behind the vapotron effect. This research builds the experimental facilities of HyperVapotron Loop-I (HVL-I) and Pressure Water HyperVapotron Loop-II (PWHL-II) to implement the subcooled boiling principle experiment in terms of typical flow parameters, geometrical parameters of test section and surface heat flux, which are similar to those of the ITER-like first wall and NBI components (EAST and MAST). The multiphase flow and heat transfer phenomena on the surface of grooves and triangular fins when the subcooled water flowed through were observed and measured with the planar laser induced fluorescence (PLIF) and high-speed photography (HSP) techniques. Particle image velocimetry (PIV) was selected to reveal vortex formation, the flow structure that promotes the vapotron effect during subcooled boiling. The coolant flow data for contributing to the understanding of the vapotron phenomenon and the assessment of how the design and operational conditions that might affect the thermal performance of the devices were collected and analysed. The subcooled flow boiling model and methods of HV heat transfer adopted in the considered computational fluid dynamics (CFD) code were evaluated by comparing the calculated wall temperatures with the experimentally measured values. It was discovered that the bubble and vortex characteristics in the HV are clearly heavily dependent on the internal geometry, flow conditions and input heat flux. The evaporation latent heat is the primary heat transfer mechanism of HV flow under the condition of high heat flux, and the heat transfer through convection is very limited. The percentage of wall heat flux going into vapour production is almost 70%. These relationships between the flow phenomena and thermal performance of the HV device are essential to study the mechanisms for the flow structure alterations for design optimization and improvements of the ITER-like devices' water cooling structure and plasma facing components for future fusion reactors.

Heat Transfer Characteristics of Subcooled Water in Circular Tubes With Twist Tapes Insert Under One-side Heating Conditions

Subcooled Flow Boiling Heat Transfer of Water in Circular Tubes with Twisted-Tape Inserts under High Heat Fluxes

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Heat Transfer Characteristics of Subcooled Flowing Boiling in Circular Tubes with and Without Swirl Tapes under High Heat Fluxes

Heat Transfer Characteristics of Subcooled Water in a Hypervapotron under High Mass Fluxes and High Heat Fluxes

Experimental Investigations on Pressure Drop for Subcooled Water in a Circular Channel with a Twisted Tape Insert under One-Side Heating Conditions

Critical Heat Flux of Highly Subcooled Water Flow Boiling in Circular Tubes with and Without Internal Twisted Tapes under High Mass Fluxes

Numerical Simulation in A Subcooled Water Flow Boiling for One-Sided High Heat Flux in Reactor Divertor

Thermo-hydraulic performance of tungsten flat tile type divertor target with two types of novel engineered cooling channel wall

Experimental Investigation on Heat Transfer of HEMJ Type Divertor with Narrow Gap Between Nozzle and Impingement Surface

Experimental Design and Analysis for Film Boiling Heat Transfer in a Circular Tube

Experimental Investigation on Heat Transfer Characteristics of a Novel Hypervapotron Channel for Divertor Target in Nuclear Fusion Reactors

Numerical study on heat transfer characteris tics of supercritical water in straight and helical tubes

Flow boiling heat transfer and pressure fluctuation characteristics in a divergent channel with inclined downward-facing heater

Analyses of Monoblocks Divertor at One-Sided High Heat Flux Using RPI Wall Boiling Model

NUMERICAL INVESTIGATION ON HEAT TRANSFER TO SUPERCRITICAL WATER FLOWING UPWARD IN A 4-M LONG BARE VERTICAL CIRCULAR TUBE

Experimental and Numerical Investigation of HyperVapotron Heat Transfer

Numerical Analysis on Heat Transfer Enhancement of Sco2 in the Tube with Twisted Tape

Numerical Simulation on Heterogeneous Heat Transfer in Water at Supercritical Pressures in Inclined Upward Tubes

Experimental study of subcooled flow boiling heat transfer of water in a circular channel under one-side heating conditions

Investigation on Heat Transfer of In-Tube Supercritical Water Cooling Accompanying Out-Tube Pool Boiling