Abstract:Lithium oxygen(Li-O 2 ) batteries have been recognized as one of the next-generation power sources, capable of supplying power for a long time even in an independent extreme environment. In spite of the theoretical advantage, Li-O 2 batteries face technical and economical challenges that must be addressed to promote them as commercially variable techcologies for future energy system. Above all, battery performance largely depends on the activities of the cathode during discharge and charge, respectively. The undesirable overpotential caused by sluggish reaction kinetics assiciated with the ORR and OER greatly limit the current performance of Li-O 2 batteries, which must be improved by efficient catalyzing the reactions. Among the numerous catalysts, perovskite oxides have attention for candidate electrocatalyst for Li-O 2 batteries due to their high electronic/ionic conductivity, high electrochemical stability, and catalytic activity. Especially, La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) is considered as a typical catalyst for Li-O 2 batteries, which and provide high oxygen surface exchange coefficient for fast kinetics at the gas/electrode interface. The surface area is significantly related on the ORR and OER performance, which influences on the active area for reactions. In this study, we have tried to utilize a simple high energy ball milling process to investigate the electrochemical properties of LSCF catalyst. Through the BET analysis, it was confirmed that the specific area significantly was increased after ball milling due to the reduced particle size, obtaining the optimized milling time with the higher ORR performance. The electrochemical activities have been measured with rotating disk electrode(RRDE) method. Well-ball milled LSCF catalyst has resulted in the enlargement of specific surface area and increased defective sites, which improve the catalytic activity. To investigate the influence of LSCF oxides on the ORR process, the performance of composite electrode with LSCF catalyst in LITFSI in either solvents has been compared with a carbon based cathode(carbon nano tube(CM130)). From the discharge results, the composite electrode showed the superior performance as well as higher specific capacitance (more than 1.6 times) than carbon based electrode dye to the altered transport and reaction kinetics due to LSCF. In this study, we have proposed the processes of obtaining a catalyst with optimal electrochemical properties through a relatively simple process and applied it to electrode for lithium oxygen batteries.

Perovskite La0.6sr0.4co0.2fe0.8o3 As An Effective Electrocatalyst For Non-Aqueous Lithium Air Batteries

Perovskite Structure LaNi0.5Fe0.5O3 Electrocatalyst for Rechargeable Li-O2 Batteries

Perovskite Sr0.9Y0.1CoO3-delta Nanorods Modified with CoO Nanoparticles as a Bifunctional Catalyst for Rechargeable Li-O-2 Batteries

La-based perovskites for capacity enhancement of Li-O2 batteries

Engineering Fe and V Coordinated Bimetallic Oxide Nanocatalyst Enables Enhanced Polysulfides Mediation for High Energy Density Li-S Battery.

Adjusting the Covalency of Metal–Oxygen Bonds in LaCoO 3 by Sr and Fe Cation Codoping to Achieve Highly Efficient Electrocatalysts for Aprotic Lithium–Oxygen Batteries

Oxygen-Deficient Ferric Oxide As an Electrochemical Cathode Catalyst for High-Energy Lithium-Sulfur Batteries.

A partially Fe-substituted perovskite electrode for enhancing Zn-CO 2 batteries

Improved Catalytic Properties of Fluorine-Doped La0.6Sr0.4Co0.2Fe0.8O3-δ for Air Electrode with High-Performance Metal-Air Batteries

Precise Engineering of Octahedron‐Induced Subcrystalline CoMoO4 Cathode Catalyst for High‐Performance Li–Air Batteries

Hierarchical Mesoporous/Macroporous Perovskite La0.5sr0.5coo3-X Nanotubes: A Bifunctional Catalyst with Enhanced Activity and Cycle Stability for Rechargeable Lithium Oxygen Batteries

Synergized Multimetal Oxides with Amorphous/Crystalline Heterostructure as Efficient Electrocatalysts for Lithium–Oxygen Batteries

Efficient Fe3C-CF Cathode Catalyst Based on the Formation/Decomposition of Li2−xO2 for Li-O2 Batteries

Study on the Effect of Surface Area on the ORR Performance of Perovskite Catalyst for High Performance Lithium-Oxygen Batteries

The Role of the A-Site Cation on the Bifunctional Electrocatalytic Activities of Ln0.5Sr0.5CoO3-δ (ln = La, Pr and Sm) for Rechargeable Zinc–Air Batteries

Mesoporous Co3O4 -Rods-Entangled Carbonized Polyaniline Nanotubes as an Efficient Cathode Material toward Stable Lithium-Air Batteries

Highly polar CoP/Co2P heterojunction composite as efficient cathode electrocatalyst for Li-air battery

High‐Performance Platinum‐Perovskite Composite Bifunctional Oxygen Electrocatalyst for Rechargeable Zn–Air Battery

Perovskite Transition Metal Oxide of Nanofibers as Catalytic Hosts for Lithium–Sulfur Battery

Regulating the Interfacial Electron Density of La 0.8 Sr 0.2 Mn 0.5 Co 0.5 O 3 /RuO x for Efficient and Low-Cost Bifunctional Oxygen Electrocatalysts and Rechargeable Zn-Air Batteries

Boosting the Electrocatalytic Oxygen Evolution of Perovskite LaCo1- x Fex O3 by the Construction of Yolk-Shell Nanostructures and Electronic Modulation