Abstract:Lithium oxygen(Li-O 2 ) batteries have been recognized as one of the next-generation power sources, capable of supplying power for a long time even in an independent extreme environment. In spite of the theoretical advantage, Li-O 2 batteries face technical and economical challenges that must be addressed to promote them as commercially variable techcologies for future energy system. Above all, battery performance largely depends on the activities of the cathode during discharge and charge, respectively. The undesirable overpotential caused by sluggish reaction kinetics assiciated with the ORR and OER greatly limit the current performance of Li-O 2 batteries, which must be improved by efficient catalyzing the reactions. Among the numerous catalysts, perovskite oxides have attention for candidate electrocatalyst for Li-O 2 batteries due to their high electronic/ionic conductivity, high electrochemical stability, and catalytic activity. Especially, La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) is considered as a typical catalyst for Li-O 2 batteries, which and provide high oxygen surface exchange coefficient for fast kinetics at the gas/electrode interface. The surface area is significantly related on the ORR and OER performance, which influences on the active area for reactions. In this study, we have tried to utilize a simple high energy ball milling process to investigate the electrochemical properties of LSCF catalyst. Through the BET analysis, it was confirmed that the specific area significantly was increased after ball milling due to the reduced particle size, obtaining the optimized milling time with the higher ORR performance. The electrochemical activities have been measured with rotating disk electrode(RRDE) method. Well-ball milled LSCF catalyst has resulted in the enlargement of specific surface area and increased defective sites, which improve the catalytic activity. To investigate the influence of LSCF oxides on the ORR process, the performance of composite electrode with LSCF catalyst in LITFSI in either solvents has been compared with a carbon based cathode(carbon nano tube(CM130)). From the discharge results, the composite electrode showed the superior performance as well as higher specific capacitance (more than 1.6 times) than carbon based electrode dye to the altered transport and reaction kinetics due to LSCF. In this study, we have proposed the processes of obtaining a catalyst with optimal electrochemical properties through a relatively simple process and applied it to electrode for lithium oxygen batteries.

Improved Catalytic Properties of Fluorine-Doped La0.6Sr0.4Co0.2Fe0.8O3-δ for Air Electrode with High-Performance Metal-Air Batteries

Engineering Phosphorus-Doped LaFeO3-δ Perovskite Oxide As Robust Bifunctional Oxygen Electrocatalysts in Alkaline Solutions

Perovskite Sr0.9Y0.1CoO3-delta Nanorods Modified with CoO Nanoparticles as a Bifunctional Catalyst for Rechargeable Li-O-2 Batteries

Efficient oxygen evolution reaction in SrCo0.8Fe0.2O3-δ perovskite and surface reconstruction for practical zinc-air batteries

Improving Ruddlesden-Popper Electrocatalysts Through Interstitial Fluorination-Driven Rearrangements of Local Coordination Environment

Anion Fluorine-Doped La<sub>0.6</sub>Sr<sub>0.4</sub>Fe<sub>0.8</sub>Ni<sub>0.2</sub>O<sub>3- </sub> Perovskite Cathodes with Enhanced Electrocatalytic Activity for Solid Oxide Electrolysis Cell Direct CO<sub>2</sub> Electrolysis

Boosting Bifunctional Catalytic Activity of Perovskite Nanoparticles for Rechargeable Zn-air Batteries

Perovskite La0.6sr0.4co0.2fe0.8o3 As An Effective Electrocatalyst For Non-Aqueous Lithium Air Batteries

Enhancement of the electrochemical properties for La0.6Sr0.4Co0.2Fe0.8O3−δ oxygen electrode by the addition of CaxCo4O9+δ nano-catalysts

Rational A/B Site Ion Doping to Design Efficient and Stable Pr0.5Ba0.4Ca0.1Fe1-xCoxO3-δ Perovskites As Zinc–Air Batteries Cathode

La-Doped Ba0.5Sr0.5Co0.8Fe0.2O3−δ Air Electrodes with Enhanced Performance and Stability for Reversible Protonic Ceramic Cells

Adjusting the Covalency of Metal–Oxygen Bonds in LaCoO 3 by Sr and Fe Cation Codoping to Achieve Highly Efficient Electrocatalysts for Aprotic Lithium–Oxygen Batteries

Organic ligand-facilitated in situ exsolution of CoFe alloy over Ba0.5Sr0.5Co0.8Fe0.2O3 perovskite toward enhanced oxygen electrocatalysis for rechargeable Zn-air batteries

Study on the Effect of Surface Area on the ORR Performance of Perovskite Catalyst for High Performance Lithium-Oxygen Batteries

Effect of B Sites on the Catalytic Activities for Perovskite Oxides La.6Sr.4CoxFe1-xO3-δ As Metal-Air Batteries Catalysts

Improving the Electrocatalytic Activity and Durability of the La0.6Sr0.4Co0.2Fe0.8O3-delta Cathode by Surface Modification

Boosting the Bifunctional Electrocatalytic Activity of Cobalt Free Perovskite Oxide (la0.8sr0.2)0.95mno3 Via Iron Doping for High-Efficiency Zn–air Batteries

Boosting the Electrocatalytic Oxygen Evolution of Perovskite LaCo1- x Fex O3 by the Construction of Yolk-Shell Nanostructures and Electronic Modulation

The Role of the A-Site Cation on the Bifunctional Electrocatalytic Activities of Ln0.5Sr0.5CoO3-δ (ln = La, Pr and Sm) for Rechargeable Zinc–Air Batteries

Enhancing ORR/OER active sites through lattice distortion of Fe-enriched FeNi3 intermetallic nanoparticles doped N-doped carbon for high-performance rechargeable Zn-air battery

Enhancement on PrBa0.5Sr0.5Co1.5Fe0.5O5 Electrocatalyst Performance in the Application of Zn-Air Battery