Abstract:Abstract With increasing aerodynamic and thermal loads, film cooling has been a popular technology integrated into the design of the modern gas turbine vane endwall, especially for the first-stage vane endwall. A staggering amount of research has been completed to quantify the effect of operating conditions and cooling hole geometrical properties. However, most of these investigations did not address the influence of the manufacturing tolerances, assembly errors, and operation degradations on the endwall misalignment. In this paper, uncertainty quantification (UQ) analysis was performed to quantify the impacts of upstream endwall misalignment uncertainties on the endwall film cooling performance and vane surface phantom cooling performance. The upstream endwall misalignment, step geometry with various step heights, commonly exists between the combustor exit and the first-stage vane endwall. Based on the non-intrusive polynomial chaos expansion (NIPC) and the uniform probability distribution assumption, the deviation (step height) uncertainties of the upstream endwall misalignment were quantified. To predict the endwall secondary flow and film cooling effectiveness in the transonic linear vane passage, the commercial computational fluid dynamic solver ANSYS FLUENT was used to numerically solve the three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) equations. The robustness analysis of endwall film cooling performance and phantom cooling performance to the upstream endwall misalignment was conducted for three design upstream step heights (ΔH): a baseline configuration (ΔH = 0 mm), two misaligned configurations with forward step (ΔH = −5 mm) and backward step (ΔH = 5 mm), respectively. Results show that the actual cooling performance has a high probability of deviating from the nominal value for the baseline configuration. The critical regions that are most sensitive to the upstream step misalignment are also identified by variances. The UQ results also show that the design geometry with a forward step has a more robust film cooling performance on endwall and phantom cooling performance on the vane pressure side surface, which means a smaller variance and a better expectation than the no-step configuration. In contrast, the design geometry with a backward step induces the reductions in the expectation of the film cooling effectiveness and coolant coverage and the amplification of performance fluctuations. This work provides a certain guiding direction for the optimization design for the upstream step geometry.

Phantom Cooling Of Nozzle Trailing Edge Discharge On Blade Surface And Platform

Study on Effects of Modern Turbine Blade Coolant Injecting Nozzle Position on Film Cooling and Vortex Composite Performance under Rotating Conditions

Turbine Platform Phantom Cooling from Airfoil Film Coolant, with Purge Flow

Transpiration Cooling of High Pressure Turbine Vane with Optimized Porosity Distribution

Unsteady Characteristic of Film Cooling and Phantom Cooling on the First Stage of a Gas Turbine:Part 2-Blade Cascade

Experimental Investigation of Turbine Phantom Cooling on Endwall with Trailing Edge Discharge Flow

Experimental study about the tip phantom cooling with different cooling-hole configurations on the blade-surface

Experimental and Numerical Investigations into the Blade Tip Phantom Cooling Performance

Effects Of Inlet Swirl On Suction Side Phantom Cooling

Comparisons of blade tip phantom cooling effectiveness for two tip structures with three tip clearances

Effects of tip structure on the turbine blade tip phantom cooling performance

Experimental Investigation of Turbine Phantom Cooling on Suction Side with Combustor-Turbine Leakage Gap Flow and Endwall Film Cooling

Turbine Blade Tip and Casing Phantom Cooling from Blade-Surface Film Coolant

Experimental investigations on cooling characteristics of different trailing-edge cutback geometries

Impact of Blade Leading Edge Film Coolant on the Blade Tip Phantom Cooling

Uncertainty Quantification on the Cooling Performance of a Transonic Turbine Vane With Upstream Endwall Misalignment

Effects of proactive phantom cooling on turbine endwall aerodynamic and film cooling performances considering aggressive swirling inflow

Aero-thermal Performance of Coolant Released from Suction Surface in a High-Pressure Turbine Cascade

Effects of Suction Surface Near Tip Coolant Injection on the Aerodynamics of Tip Leakage Flow in a High-Pressure Turbine Cascade

Numerical Simulation for Heat Transfer Properties at Trailing Edge of Gas Turbine Airfoils

Film cooling enhancement over oblong-dimpled cutback surfaces for the trailing edge of turbine blades