Abstract:Abstract With increasing aerodynamic and thermal loads, film cooling has been a popular technology integrated into the design of the modern gas turbine vane endwall, especially for the first-stage vane endwall. A staggering amount of research has been completed to quantify the effect of operating conditions and cooling hole geometrical properties. However, most of these investigations did not address the influence of the manufacturing tolerances, assembly errors, and operation degradations on the endwall misalignment. In this paper, uncertainty quantification (UQ) analysis was performed to quantify the impacts of upstream endwall misalignment uncertainties on the endwall film cooling performance and vane surface phantom cooling performance. The upstream endwall misalignment, step geometry with various step heights, commonly exists between the combustor exit and the first-stage vane endwall. Based on the non-intrusive polynomial chaos expansion (NIPC) and the uniform probability distribution assumption, the deviation (step height) uncertainties of the upstream endwall misalignment were quantified. To predict the endwall secondary flow and film cooling effectiveness in the transonic linear vane passage, the commercial computational fluid dynamic solver ANSYS FLUENT was used to numerically solve the three-dimensional steady-state Reynolds-Averaged Navier–Stokes (RANS) equations. The robustness analysis of endwall film cooling performance and phantom cooling performance to the upstream endwall misalignment was conducted for three design upstream step heights (ΔH): a baseline configuration (ΔH = 0 mm), two misaligned configurations with forward step (ΔH = −5 mm) and backward step (ΔH = 5 mm), respectively. Results show that the actual cooling performance has a high probability of deviating from the nominal value for the baseline configuration. The critical regions that are most sensitive to the upstream step misalignment are also identified by variances. The UQ results also show that the design geometry with a forward step has a more robust film cooling performance on endwall and phantom cooling performance on the vane pressure side surface, which means a smaller variance and a better expectation than the no-step configuration. In contrast, the design geometry with a backward step induces the reductions in the expectation of the film cooling effectiveness and coolant coverage and the amplification of performance fluctuations. This work provides a certain guiding direction for the optimization design for the upstream step geometry.

Effects of proactive phantom cooling on turbine endwall aerodynamic and film cooling performances considering aggressive swirling inflow

Study on Effects of Modern Turbine Blade Coolant Injecting Nozzle Position on Film Cooling and Vortex Composite Performance under Rotating Conditions

An Experimental Study of Turbine Vane Film Cooling Using Endoscope-Based PSP Technique in a Single-Passage Wind Tunnel

Effect of non-axisymmetric endwall contouring and swirling inlet flow on film cooling performance of turbine endwall

Non-axisymmetric endwall contour optimization and performance assessment as affected by simulated swirl purge flow and backward hole injection

Effects of the positive pre-swirl purge flow on endwall aero-thermal performance of a gas turbine blade

Influence of coolant mass flow rate on the endwall conjugate heat transfer

Experimental study of the effect of swirling inflow on film cooling effectiveness

Gas turbine endwall film cooling and heat transfer characteristics with a multi-cavity slashface gap design

Experimental Investigation of Turbine Phantom Cooling on Endwall with Trailing Edge Discharge Flow

Cooling Effectiveness and Aerodynamic Performance in a 2D-Contoured Endwall Passage with Different Mass Flow Ratios

Experimental and numerical investigations of overall cooling effectiveness on a vane endwall with jet impingement and film cooling

Investigation on the showerhead film cooling of the turbine vane considering combustor swirling outflow

Effects Of Inlet Swirl On Suction Side Phantom Cooling

Experimental Investigation of Turbine Phantom Cooling on Suction Side with Combustor-Turbine Leakage Gap Flow and Endwall Film Cooling

Effects of Endwall 3D Contouring on Film Cooling Effectiveness of Cylindrical Hole Injections at Different Locations on Vane Endwall

Uncertainty Quantification on the Cooling Performance of a Transonic Turbine Vane With Upstream Endwall Misalignment

Endwall Film Cooling Performance for a First-Stage Guide Vane with Upstream Combustor Walls and Inlet Injection

Experimental and numerical study on film cooling effectiveness of an annular cascade endwall with different slot configuration

Improving Turbine Endwall Overall Cooling Effectiveness Using Curtain Cooling and Redistributed Film-Hole Layouts: An Experimental and Computational Study

Effects of non-axisymmetric endwall contouring on aerothermal performance of a gas turbine blade endwall with a purge flow