Abstract:Fundamental studies of a new thermal annealing strategy for maximizing proton conductivity and single cell performance of glassy sulfonated hydrocarbon fuel cell membrane materials under both fully and partially hydrated conditions are reported. Directly copolymerized disulfonated poly(arylene ether sulfone) random copolymers (BisA-XX, XX is the mole percent of hydrophilic moieties, XX = 20 to 40) with 2,2'-isopropylidene diphenol swivel ((CH3)(2)-C) units in their polymer backbone were cast from N,N-dimethylacetamide (DMAc) and dried under two different protocols; one set was dried at 60 degrees C (BisA-XX_60 degrees C), and the other at 150 degrees C under vacuum immediately after the initial drying (BisA-XX_150 degrees C). Small amounts of DMAc solvent remained during the second drying step which depressed the glass transition temperatures (T-g) of the BisA copolymers lower than 150 degrees C. BisA-XX_150 degrees C samples were essentially thermally annealed when dried at 150 degrees C. This increased the density of BisA copolymer chains; their T-g values were increased. Moreover, T-1 values of the protons in BisA-XX aromatic phenylene rings measured via solid-state NMR technique were lower as a result of the improved H-1-H-1 dipolar interaction. Interestingly, proton conductivity was improved after thermal annealing, possibly because the sulfonic acid density in the fully hydrated state (i.e., IECv(wet)) was enhanced. The synergistic effect of reduced water uptake and more developed hydrophilic-hydrophobic nanochannel formation may be important. The thermal annealing significantly influenced proton conductivity particularly at a low humidity (30 to 80% relative humidity (RH)). As a result, BisA-XX_150 degrees C samples derived from identical materials exhibited electrochemical polymer electrolyte membrane fuel cell (PEMFC) performances similar and superior to Nafion (R) 112 and BisA-XX_60 degrees C samples measured at 65% RH at 80 degrees C, respectively.

A Capillary Water Retention Effect to Improve Medium-Temperature Fuel Cell Performance

Synergistic Effect of 2-Acrylamido-2-methyl-1-propanesulfonic Acid on the Enhanced Conductivity for Fuel Cell at Low Temperature

Solvent-assisted Thermal Annealing of Disulfonated Poly(arylene Ether Sulfone) Random Copolymers for Low Humidity Polymer Electrolyte Membrane Fuel Cells

Hydrophobicity enhancement of gas diffusion layer induced by hydrothermal deposition process and the electrochemical performance of proton exchange membrane fuel cell

Liquid Water Transport and Mechanical Performance of Electrospun Gas Diffusion Layers

Asymmetric Polymer Electrolyte Membranes for Water Management of Fuel Cells

Molecular Dynamics Simulation of the Mechanical Properties and Thermal Conductivity of Aromatic Electrolytes in Proton Exchange Membrane Fuel Cells

Uncoupling Characteristics Of Temperature And Relative Humidity Distribution In A Commercial-Size Polymer Electrolyte Membrane Fuel Cell

The importance of water transport on short-side chain perfluorosulfonic acid membrane fuel cells operating under low relative humidity

DIRECT SYNTHESIS AND PROPRTIES OF SULFONATED POLY(ARYLENE ETHER SULFONE) COPOLYMERS FOR PROTON EXCHANGE MEMBRANES IN FUELCELLS

High-temperature low-humidity proton exchange membrane with "stream-reservoir" ionic channels for high-power-density fuel cells

Improvement of Electrochemical Performances of Sulfonated Poly(arylene Ether Sulfone) Via Incorporation of Sulfonated Poly(arylene Ether Benzimidazole)

High flexible ether-free semi-crystalline fuel cell membranes: Molecular-level design, assembly structure and properties

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

SCTF Nanosheets@sulfonated Poly (P-Phenylene-co-aryl Ether Ketone) Composite Proton Exchange Membranes for Passive Direct Methanol Fuel Cells

Synthesis and Characterization of Sulfonated Poly(arylene Ether Sulfone) Copolymers Containing Carboxyl Groups for Direct Methanol Fuel Cells

Recent Progress in the Development of Sulfonated Hydrocarbon Polymers for Fuel Cell Application(Ⅱ)

Synthesis of Sulfonated Poly(Imidoaryl Ether Sulfone) Membranes for Polymer Electrolyte Membrane Fuel Cells

Effects of hydrophobic side chains in poly(fluorenyl-<i>co</i>-aryl piperidinium) ionomers for durable anion exchange membrane fuel cells

Proton Conducting, Composite Sulfonated Polymer Membrane for Medium Temperature and Low Relative Humidity Fuel Cells

Single-walled carbon nanotube interlayer modified gas diffusion layers to boost the cell performance of self-humidifying proton exchange membrane fuel cells