Abstract:A NiO-YSZ anode-supported hollow fiber solid oxide fuel cell (HF-SOFC) has been fabricated with redox stable (La0.75Sr0.25)(0.95)Cr0.5Mn0.5O3-delta-Sm0.2Ce0.8O1.9-YSZ (LSCM-SDC-YSZ) composite cathode. The characterization of NiO-YSZ hollow fibers prepared by the phase inversion method is focused on the microstructure, porosity, bending strength and electrical conductivity. A thin YSZ electrolyte membrane (about 10 mu m) can be prepared by a vacuum-assisted dip-coating process and is characterized in terms of microstructure and gas-tightness. The performance of the as-prepared HF-SOFC is investigated at 750-850 degrees C with humidified H-2 as fuel and ambient air as the oxidant. The peak power densities of 513, 408 and 278 mW cm(-2) can be obtained at 850, 800 and 750 degrees C, respectively, and the corresponding interfacial polarization resistances are 0.14, 0.29 and 0.59 Omega cm(2). The high performance at intermediate-to-high temperatures could be attributed to thin electrolyte and proper composite cathode with low interfacial polarization resistance. The low interfacial polarization resistance suggests potential applications of LSCM-SDC-YSZ composite oxides as the redox stable cathode. This investigation indicates that the redox stable LSCM-SDC-YSZ is a promising cathode material system for the next generation YSZ-based HF-SOFC. The results will be expected to open up a new phase of the research on the micro-tubular SOFCs. (C) 2010 Professor T. Nejat Veziroglu. Published by Elsevier Ltd. All rights reserved.

Fabrication of anode-supported Sc2O3-stabilized-ZrO2 electrolyte micro-tubular Solid Oxide Fuel Cell by phase-inversion and dip-coating

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Anode-supported ScSZ-electrolyte SOFC with whole cell materials from combined EDTA–citrate complexing synthesis process

An Anode-Supported Micro-Tubular Solid Oxide Fuel Cell with Redox Stable Composite Cathode

Micro-Tubular Solid Oxide Fuel Cell with Asymmetric Structure Anode and La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

An anode-supported hollow fiber solid oxide fuel cell with (Pr0.5Nd0.5)0.7Sr0.3MnO3-δ-YSZ composite cathode

Fabrication of Metal-Supported Tubular Solid Oxide Fuel Cell by Phase-Inversion Method and in Situ Reduction

Al2O3 Toughening ScSZ Electrolyte Fabricated by Water-Based Tape Casting Technique for Solid Oxide Fuel Cells

Development of yttria-stabilized zirconia thin films via slurry spin coating for intermediate-to-low temperature solid oxide fuel cells

Fabrication and Optimization of La 0.4 Sr 0.6 Co 0.2 Fe 0.7 Nb 0.1 O 3- Δ Electrode for Symmetric Solid Oxide Fuel Cell with Zirconia Based Electrolyte

Co-sintering of gradient anode – electrolyte structure for microtubular SOFC

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Fabrication and Electrochemical Characterization of Anode-Supported Microtubular Solid Oxide Fuel Cells Based on Ce0.8sm0.2o2-D Electrolytes

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Fabrication and Performance of Anode-Supported Electrolyte Thin Films SOFCs

High Performance Tubular Solid Oxide Fuel Cells With Bscf Cathode

A High-Strength Solid Oxide Fuel Cell Supported by an Ordered Porous Cathode Membrane

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray