Abstract:Background: High-frequency ultrasonic transducer arrays are essential for high resolution imaging in clinical analysis and Non-Destructive Evaluation (NDE). However, the structure design and fabrication of the kerfed ultrasonic array is quite challenging when very high frequency (>= 100 MHz) is required.Objective and method: Here we investigate the effect of kerf depth on the performances of array transducers. A finite element tool, COMSOL, is employed to simulate the properties of acoustic field and to calculate the electrical properties of the arrays, including crosstalk effect and electrical impedance. Furthermore, Inductively Coupled Plasma (ICP) deep etching process is used to etch 36 degrees/Y-cut lithium niobate (LiNbO3) crystals and the limitation of etching aspect ratio is studied. Several arrays with different profiles are realized under optimized processes. At last, arrays with a pitch of 25 mu m and 40 mu m are fabricated and characterized by a network analyzer.Results: Kerf depth plays an important role in the performance of the transducer array. The crosstalk is proportional to kerf depth. When kerf depth is more than 13 mu m, the array with crosstalk less than -20 dB, which is acceptable for the real application, could provide a desired resolution. Compared to beam focusing, kerf depth exhibits more effect on the beam steering/focusing. The lateral pressure distribution is quantitatively summarized for four types of arrays with different kerf depth. The results of halfcut array are similar to those of the full-cut one in both cases of focusing and steering/focusing. The Full-Width-at-Half-Maximum (FWHM) is 55 mu m for the half-cut array, and is 42 mu m for the full-cut one. The 5-mu m-cut array, suffering from severe undesired lobes, demonstrates similar behaviors with the no-cut one. ICP process is used to etch the 36 degrees/Y-cut LiNbO3 film. The aspect ratio of etching profile increases with the kerf width decreasing till it stops by forming a V-shaped groove, and the positive tapered profile angle ranges between 62 degrees and 80 degrees. If the mask selectivity does not limit the process in terms of achievable depth, the aspect ratio is limited to values around 1.3. The measurement shows the electrical impedance and crosstalk are consistent with the numerical calculation.Conclusion: The numerical results indicate that half-cut array is a promising alternative for the fabrication of high-frequency ultrasonic linear arrays. In fact, the minimum pitch that could be obtained is around 25 mu m, equivalent to a pitch of 1.6 lambda, with a kerf depth of 16 mu m under the optimized ICP parameters. Crown Copyright (C) 2011 Published by Elsevier B. V. All rights reserved.

Effect of Kerf Filler on the Electromechanical Coupling Coefficient of an Ultrasonic Transducer Array Element

Electromechanical Coupling Coefficient of an Ultrasonic Array Element

Effect of kerf filler on the electromechanical coupling coefficient of 1–3 piezoelectric composites

Research of Coupling Coefficient Extraction of a Cavity Resonator

Finite Element Analysis and Theoretical Model of Slotted Cymbal Composite Piezoelectric Transducer

Aspect Ratio Dependence of Electromechanical Coupling Coefficient of Piezoelectric Resonators

Research on Effective Electric-Mechanical Coupling Coefficient of Sandwich Type Piezoelectric Ultrasonic Transducer Using Bending Vibration Mode

Numerical and Experimental Investigation of Kerf Depth Effect on High-Frequency Phased Array Transducer

The electromechanical coupling property and vibration behavior in 1-3 type piezoelectric composites

Extraction of electromechanical coupling coefficient of piezoelectric thin films deposited on substrates

Finite Element Analysis and Experimental Studies on the Thickness Resonance of Piezocomposite Transducers

Coupling Effects of Crosstalk and Parasitic Loss on Capacitive Micromachined Ultrasonic Transducers

Effect of Shared Cavity on Electromechanical Performance of Piezoelectric Based Micro-machined Ultrasonic Transducer Array.

FEM model and simulation effect of electrode shape on transverse coupling wave in FBAR sensor

Finite Element and Experimental Study of Impedance Matching Layer Optimization

Research on a high-frequency unfilled layered symmetrical piezoelectric material with a high effective electromechanical coupling coefficient

Parametric Analysis and Optimization of Radially Layered Cylindrical Piezoceramic/Epoxy Composite Transducers

Effect of Filling Material Properties on 1–3 Piezoelectric Composite Performance

Performance and Crosstalk Evaluation of 2-D Array Piezoelectric Micromachined Ultrasonic Transducer with 3-D Finite Element Simulation

The Electro-Mechanical Behaviour Of Flexural Ultrasonic Transducers

Studies on Electromagnetic Coupling Characteristics for Apertures on Metallic Cylinders