Adsorption of Co2 on A Micro-/Mesoporous Polyimine Modified with Tris(2-Aminoethyl)Amine

Chao Xu,Zoltan Bacsik,Niklas Hedin

DOI: https://doi.org/10.1039/c5ta01321f

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:Tris(2-aminoethyl)amine modified micro-/mesoporous polyimine shows high CO2 uptakes at low partial pressures and high estimated CO2-over-N2 selectivity up to 1040.

What problem does this paper attempt to address?

Polyethylenimine-Grafted Hkust-Type Mof/Poiyhipe Porous Composites (Pei@Pgd-H) As Highly Efficient Co(2 )Adsorbents

Junjie Zhu,Linbo Wu,Zhiyang Bu,Suyun Jie,Bo-Geng Li

DOI: https://doi.org/10.1021/acs.iecr.9b00213

2019-01-01

Industrial & Engineering Chemistry Research

Abstract:Searching for highly efficient and robust CO2 adsorbents is very important for CO2 capture, utilization, and storage. In this study, new polyethylenimine-grafted metal-organic framework (MOF)-polymer composites, abbreviated as PEI@PGD-H, were synthesized via high internal phase emulsion (HIPE) template polymerization of divinylbenzene and glycidyl methacrylate, followed by in situ generation of HKUST-type MOF in the presence of hydrophobic-modified CuO nanoparticles via the reaction of CuO with 1,3,5-benzenetricarboxylic acid and then polyethylenimine (PEI) functionalization via epoxy-amine reaction and amine-metal sites interaction. The coexistence of the hierarchical interconnected porous skeleton of poly(glycidyl methacrylate-divinylbenzene) (PGD), high specific surface area of MOF, and chemical CO2 adsorption of PEI endows PEI@PGD-H with high CO2 adsorption capacity, rate, and selectivity. PEI7O@PGD-H shows a CO2/N-2 separation factor as high as 76 and CO2 adsorption capacities of 4.3, 3.0, and 1.8 mmol of CO2/g from pure CO2, simulated flue gas, and air, respectively. After 20 CO2 adsorption-desorption cycles, the adsorbent still retained a high and stable CO2 capture capacity over 2.8 mmol of CO2/g for simulated flue gas. The adsorbent also displays reasonably good thermal stability, excellent water endurance, low desorption energy, and easy shaping. The desorption heat is as low as 48 kJ/mol of CO2. These features make PEI@PGD-H highly efficient, robust, and low-energy CO2 adsorbents for practical application in CO2 capture.
Synthesis and CO2 Capture Behavior of Porous Cross-Linked Polymers Containing Pendant Triazole Groups

Junjie Zhu,Linbo Wu,Zhiyang Bu,Suyun Jie,Bo-Geng Li

DOI: https://doi.org/10.1021/acs.iecr.7b01961

2017-01-01

Industrial & Engineering Chemistry Research

Abstract:Porous cross-linked polymers containing pendant triazole groups were synthesized from glycidyl methacrylate (GMA) in the presence of divinylbenzene via high internal phase emulsion (HIPE) templating method followed by functionalization with sodium 3-amino-1,2,4-triazole (ATANa). They were characterized with FTIR, SEM, BET, and mercury intrusion and assessed as CO2 adsorbents. With interconnected hierarchical porous structure and abundant triazole groups which absorbed CO2 chemically in 1:1 stoichiometry, the adsorbents exhibited high CO2 adsorption capacity (3.6 mmol g(1), at 25 degrees C and 1 atm) and rate, and good CO2/N-2 selectivity (similar to 30). The adsorbents also displayed easy CO2 desorption with medium desorption heat (58 kJ/mol CO2), acceptable moisture endurance, and excellent recyclability. The results suggest that these functionalized porous polymers are potential adsorbents for CO2 capture
Polyethyleneimine-Modified UiO-66-NH2(Zr) Metal–Organic Frameworks: Preparation and Enhanced CO2 Selective Adsorption

Junjie Zhu,Linbo Wu,Zhiyang Bu,Suyun Jie,Bo-Geng Li

DOI: https://doi.org/10.1021/acsomega.8b02319

IF: 4.1

2019-01-01

ACS Omega

Abstract:UiO-66-NH2, a zirconium-based functional metal–organic framework (MOF), was postsynthetically modified via Schiff base reaction between aldehyde groups in glutaraldehyde and amino groups in UiO-66-NH2 and CO2-preabsorbed polyethyleneimine (PEI). The resulting PEI-modified MOFs, abbreviated as PEIC@UiO, were characterized with 1H NMR, Fourier transform infrared, powder X-ray diffraction, Brunauer–Emmett–Teller, scanning electron microscopy, and thermogravimetric analysis and evaluated as CO2 adsorbents. In comparison with pristine UiO-66-NH2, the PEIC@UiO adsorbents have reduced specific surface area (7–150 m2/g) but maintained the same crystal structure. Particularly, the PEIC96@UiO adsorbent exhibited significantly improved CO2/N2 adsorption selectivity (48 vs 25) and higher CO2 adsorption capacity (3.2 vs 2.7 mmol/g). The adsorbent also displayed moderate desorption energy (68 kJ/mol CO2), superior moisture endurance, and recyclability, which are very desirable for practical applications.
Ultramicroporous CO 2 adsorbents with tunable mesopores based on polyimines synthesized under off-stoichiometric conditions

niklas hedin

DOI: https://doi.org/10.1016/j.micromeso.2015.09.041

IF: 5.876

2016-01-01

Microporous and Mesoporous Materials

Abstract:A series of porous polymers with ultramicropores and tunable mesopores were synthesized by condensation reaction (Schiff base) of triamine and trialdehyde monomers. They had specific surface areas and pore volumes of up to 694 m2/g and 0.67 cm3/g. The ultramicropores seemed to have been templated by the solvent (DMSO) primarily. The size of the mesopores depended strongly on the amine-to-aldehyde ratio used during synthesis. With a moderate aldehyde excess, the irregular mesopores of the porous polymers increased in size. The polymers' capacities to adsorb CO2 were large (0.93–1.58 mmol/g at 0.15 bar and 2.20–3.28 mmol/g at 1 bar; 0 °C) due to their large ultramicropore volumes, and the estimated CO2-over-N2 selectivities were also relatively high (31–90 for CO2/N2 mixtures with 15 v%/85 v% at 0 °C). The uptake of CO2 on the polymers was quite rapid, and it appears advantageous to have a combination of meso- and ultramicropores in this class of polymers for applications in carbon capture and storage.
High CO2 adsorption on amine-functionalized improved macro-/mesoporous multimodal pore silica

Huangyu Yan,Guojie Zhang,Ying Xu,Qiqi Zhang,Jun Liu,Guoqiang Li,Yuqiong Zhao,Ying Wang,Yongfa Zhang

DOI: https://doi.org/10.1016/j.fuel.2022.123195

IF: 7.4

2022-05-01

Fuel

Abstract:In recent years, amine functionalized materials have attracted great interest as prospective solid adsorbents for CO2 capture. However, the amine functionalization of traditional supports (such as SBA-15, etc.) can lead to a decrease in the pore volume and specific surface area of the adsorbent, which significantly affects the CO2 adsorption–desorption kinetics. To overcome this problem, the macro-/mesoporous multimodal pore silica was quickly synthesized using a ternary nonionic surfactant as a template through a partitioned collaborative self-assembly method, and impregnated with TEPA. The prepared support HMS-4 h has bimodal pores (pore size of 9.41 nm and 90 nm), which can not only improve the dispersibility of the loaded TEPA, but also effectively reduce the diffusion resistance of CO2. At the same time, the high surface area (838 m2/g) and large pore volume (2.34 cm3/g) of HMS-4 h can further improve the adhesion and quantity of amine-based active sites. The highest adsorption capacity reaches 6.04 mmol/g for HMS-4 h-75%TEPA at 90 ℃ and 1 bar. The adsorption capacity for HMS-4 h-75%TEPA was steady after 10 adsorption–desorption cycles. BET, XRD, FT-IR, SEM, TG-DTG were used to characterize the performance of the adsorbent. The CO2 adsorption mechanism and the effects of organic amine loading, adsorption temperature and CO2 concentration on CO2 adsorption performance were systematically studied. The research shows that HMS-4 h-75%TEPA is an excellent adsorbent with high adsorption capacity in a wide temperature range, and low energy. This provides a reference for the design of high-performance solid amine CO2 adsorbents in the future.

energy & fuels,engineering, chemical
CO2 Adsorption by Polyamine-Based Protic Ionic Liquid-Functionalized Mesoporous Silica: Regenerability and Influence of Flue Gas Contaminants

Zhang Wei,Li Yu,Li Younan,Gao Erhao,Cao Guanghan,Bernards Matthew T.,University of Washington,Shi Yao

DOI: https://doi.org/10.1007/s10853-020-05451-3

IF: 4.5

2020-01-01

Journal of Materials Science

Abstract:Polyamine-based protic ionic liquid (PILs)-functionalized mesoporous silica has drawn much attention due to its high CO2 adsorption rate, high CO2 adsorption capacity, and recyclability. However, the performance of these materials under realistic operating conditions and the influence of flue gas contaminants such as SOx, NOx, and water vapor remain unexplored. In this study, the effects of these flue gas contaminants on CO2 adsorption of PILs-functionalized SBA-15 are evaluated through breakthrough experiments. The results show that the CO2 adsorption capacity and capture rate of the hybrid sorbents are increased by about one-third in the presence of trace water vapor. This is attributed to additional CO2 capture pathways with amine groups that result from the humid environment. The additional pathway was further explained with FT-IR spectroscopy and DFT calculations, which reveal that in the presence of water vapor the CO2 molecules react with amine groups to form stable zwitterionic bicarbonate ions. On the other hand, the sorbents have strong resistance to SO2 and NO over the tested concentration range of 0–500 ppm, with limited impact on CO2 capture. After 8 cyclic adsorption/regeneration experiments, the CO2 adsorption capacities of the sorbents almost are constant when compared to the first cycle performance.
Microporous Polymelamine Network for Highly Selective Co2 Adsorption

Lei Liu,Pei-Zhou Li,Liangliang Zhu,Ruqiang Zou,Yanli Zhao

DOI: https://doi.org/10.1016/j.polymer.2012.12.015

IF: 4.6

2013-01-01

Polymer

Abstract:Microporous polymelamine network was prepared through one-pot catalyst-free polymerization using the Schiff base reaction. Gas adsorption experiments indicate that the network possesses high CO2 uptake capacity, reaching 89.0 cm(3) g(-1) (17.9 wt%) at 1.0 bar and 273 K, along with high selectivity towards CO2 over N-2 and CH4. The porous polymeric network presents a promising potential as efficient adsorbents in clean energy applications. (C) 2012 Elsevier Ltd. All rights reserved.
Investigation of adsorption/desorption performance by aminopropyltriethoxysilane grafted onto different mesoporous silica for post-combustion CO2 capture

Pailin Muchan,Chintana Saiwan,Manit Nithitanakul

DOI: https://doi.org/10.1093/ce/zkaa003

2020-04-01

Clean Energy

Abstract:Abstract Mesoporous silicas with hexagonal structure (MCM-41 and SBA-15) and cubical interconnected pore structure (KIT-6) were synthesized and modified with aminopropyltriethoxysilane (APTES) for using as adsorbents in carbon-dioxide (CO2)-adsorption application. The CO2-adsorption experiment was carried out at room temperature and atmospheric pressure using 15% CO2 with a flow rate of 20 mL/min and the desorption experiment was carried out at 100°C under N2 balance with a flow rate of 20 mL/min. The adsorption capacity and adsorption rate of all modified mesoporous silicas were enhanced due to the presence of primary amine in the structure, which was able to form a fast chemical reaction with CO2. All adsorbents showed good adsorption performance stability after using over five adsorption/desorption cycles. Due to the effect of the adsorbents’ porous structure on the adsorption/desorption process, an adsorbent with sufficient pore-size diameter and pore volume together with interconnected pore, KIT-6, represents a promising adsorbent that gave the optimum adsorption/desorption performance among others. It showed reasonable adsorption capacity with a high rate of adsorption. In addition, it could also be regenerated with 99.72% efficiency using 12.07 kJ/mmolCO2 of heat duty for regeneration.
Adsorption Capacity of Carbon Dioxide on Amine Modified Mesoporous Materials with Larger Pore Sizes

Zhao Hui-Min,Lin Dan,Yang Gang,Chun Yuan,Xu Qin-Hua

DOI: https://doi.org/10.3866/pku.whxb201202071

2012-01-01

Acta Physico-Chimica Sinica

Abstract:Mesoporous silica SBA-15-like materials with large pores were synthesized using tri-block copolymer P123 as a structure-directing agent, tetramethoxysilane as the silicon source, and different organic solvents as swelling agents. The resulting materials were characterized by powder X-ray diffraction (XRD), N-2 adsorption-desorption, scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy. The results showed that the introduction of swelling agents effectively enlarged the pore diameter and pore volume of the SBA-15 materials, and pore swelling with isooctane was larger than that with CCl4. When modified with tetraethylenepentamine (TEPA), all of these composite materials exhibited excellent adsorption capacities for CO2. The adsorption capacity of CO2 was independent of the pore structure, if the template was removed before modification with TEPA. By contrast, the adsorption capacity increased with the pore diameter when the as-synthesized mesoporous material was modified with TEPA. The effects of temperature and pressure on the CO2 adsorption capacity were investigated using adsorption isotherms and CO2 temperature-programmed desorption (TPD). With CO2 adsorption at higher temperature, the composite materials showed different adsorption capacities with pressure variation. As a result, the adsorption and separation of CO2 on these TEPA modified mesoporous materials in ambient air flow can be realized via pressure swing adsorption.
Adsorption Separation of CO2 from Flue Gas by Hyperbranched Solid-Amine

SHI Jingjin

2011-01-01

Abstract:Hyperbranched solid amine was prepared with KIT-6 type mesoporous silica,which was modified by tetraethylenepentamine(TEPA)using post-synthetic impregnation.The adsorption behavior of CO2 on KIT-6(TEPA)was investigated using an adsorption column.The adsorption capacity of KIT-6(TEPA)for CO2 increased with temperature at 303—343 K,but decreased as temperature increased at 343—353 K.The maximum adsorption capacity is 3.1 mmol g-1 at 343 K.The mechanism of CO2 adsorption on KIT-6(TEPA)is mainly chemical adsorption.The adsorption capacity is improved by moisture.It reaches 3.5 mmol·g-1 in the presence of 12% water.The adsorption capacity is maintained after 20 cycles of adsorption and regeneration,indicating that the KIT-6(TEPA)is stable in a prolonged cyclic operation.Experimental breakthrough curves are fitted with a deactivation model,giving good agreement with experimental data.
Polyethyleneimine-Modified Amorphous Silica for the Selective Adsorption of CO2/N2 at High Temperatures

Cheng Li,Xiaoqing Wang,Anjie Yang,Peng Chen,Tianxiang Zhao,Fei Liu

DOI: https://doi.org/10.1021/acsomega.1c04743

IF: 4.1

2021-12-14

ACS Omega

Abstract:Mechanochemistry is very attractive as an efficient, solvent-free, and simplified technique for the preparation of composite adsorbents. Here, a series of polyethyleneimine (PEI)-modified SiO2 adsorbents were prepared via mechanical ball milling for selective adsorption of CO2 at high temperatures. The structural properties of these adsorbents were characterized by XRD, SEM, TGA, FTIR, and N2 adsorption-desorption. This method can better disperse the PEI evenly in the SiO2 as well as maintain the porous structure of the adsorbents by comparing with the impregnated adsorbents. These adsorbents presented appreciable performance in separating CO2 at high temperatures, and the CO2 adsorption capacity of PEI(70%)/SiO2 is up to 2.47 mmol/g at 70 °C and 1.5 bar, which is significantly higher than that of the same type of CO2 adsorbent reported in the literature. Furthermore, the adsorbent of PEI(70%)/SiO2 provided an ideally infinite selectivity for CO2/N2 (15:85) at 70 °C. These results showed that mechanical grinding methods are a simple and effective approach to producing amine-modified silica composite adsorbents.
Carbon Dioxide Adsorption on Amine-Impregnated Mesoporous SBA-15 Sorbents: Experimental and Kinetics Study

An Zhao,Arunkumar Samanta,Partha Sarkar,Rajender Gupta

DOI: https://doi.org/10.1021/ie3030533

2013-05-03

Abstract:In this work, an experimental and theoretical investigation was conducted on the adsorptive removal of CO2 onto tetraethylenepentamine (TEPA) functionalized mesoporous SBA-15. The functionalization of SBA-15 silica with TEPA was achieved using a conventional wet impregnation technique. The structural properties of the mesoporous silica sorbents were characterized by nitrogen adsorption/desorption, SAXS, SEM, TEM, and FTIR techniques. The adsorption of CO2 on the amine-impregnated sorbent was measured by thermogravimetric method over a CO2 partial pressure range of 10–100 kPa and a temperature range of 30–100 °C under atmospheric pressure. The effects on CO2 adsorption capacity of temperature, partial pressure of CO2, amine loading, and moisture were evaluated. All the impregnated SBA-15 sorbents showed reversible CO2 adsorption behaviors with fast adsorption kinetics. The CO2 adsorption capacity measured at different temperatures suggests that the optimal adsorption temperature is 75 °C. The CO2 uptake of the amine-impregnated sorbent increased significantly in the presence of moisture. SBA-15 containing 60 wt % TEPA showed the highest CO2 adsorption capacity of 5.22 mmol/g in pure and humid CO2 at 75 °C. Temperature swing adsorption/desorption cycles were also explored using simulated flue gas in both dry and humid conditions, and it was found that CO2 uptake after ten cycles was within 90% of CO2 uptake of the first cycle. Different adsorption kinetic models have also been investigated to analyze the experimental data of CO2 uptake. The model was validated with the experimental results of isothermal adsorption measurements of CO2 on SBA-15/TEPA. It has been found that Fractional Order kinetic model (Chem. Eng. J. 2011, 173, 72) is very good over the entire adsorption region of the study with a maximum average absolute deviation between experimental CO2 uptake and that calculated from the model of about 2.42%.

engineering, chemical
A stable solid amine adsorbent with interconnected open-cell structure for rapid CO2 adsorption and CO2/CH4 separation

Haorui Liu,Shuoyu Wang,Xiaoqiong Wang,XiaoJing Feng,Shuixia Chen

DOI: https://doi.org/10.1016/j.energy.2022.124899

IF: 9

2022-11-01

Energy

Abstract:A novel stable porous solid amine adsorbent with three-dimensional interpenetrating network structure was prepared by polymerization of divinylbenzene using high internal phase emulsion (HIPE) template method, and followed by further introducing polyethyleneimine (PEI) by impregnation-crosslinking method. Fixed bed dynamic adsorption experiment proved that under wet condition, the former exhibited not only a higher capacity of 6.22 mmol/g but also a better adsorption kinetics process with faster adsorption rate and longer lag in breakthrough point, which makes it potential to be used in gas separation. In CO2/CH4 separation experiment, PolyHIPE-PE30-4 showed a CO2/CH4 separation selectivity of 253 at 298 K and 1 bar, and meanwhile exhibited an extra-high operating capacity. The pure methane productivity of PolyHIPE-PE30-4 was 24.1 mmol/g from CO2/CH4 (80:20, v/v) mixed gas, 4.5 times to that of PE30-4 gel (5.36 mmol/g). Significantly, PolyHIPE-PE30-4 could maintain an excellent regeneration performance after at least 7 cycles, while PolyHIPE-P30 exhibited a remarkably decrease in adsorption capacity after only three adsorption-desorption process in wet condition, demonstrating the advantage of impregnation-crosslinking method for amine functionalization. The superior CO2 adsorption capacity and regeneration stability, combined with its superior adsorption kinetics property make it a broad prospect in the field of CO2/CH4 separation.

energy & fuels,thermodynamics
The Influence of Pore Size and Pore Structure of Silica-Based Material on the Amine-Modified Adsorbent for CO2 Capture

Li Lin,Siyu Han,Fanzhi Meng,Jinglin Li,Kailun Chen,Endian Hu,Jianguo Jiang

DOI: https://doi.org/10.1016/j.seppur.2024.126735

IF: 8.6

2024-01-01

Separation and Purification Technology

Abstract:Silica impregnated with amines has attracted much attention as a promising alternative to amine scrubbing. This study selected SBA-15, MCM-41, and MCM-48 as support materials and set amine types (PEI and DETA), amine loadings (20-45 %), and temperatures (40-120 degrees C) as parameters, systematically exploring the influence of pore size and pore structure on the adsorption performance. The pore size and pore structure had little impact on the type of chemical functional group and thermal stability, but played an important role in the CO2 adsorption capacity as well as the response of adsorption performance to temperature and amine. By comparison, the silica with large pore sizes was more suitable for PEI, while the silica with small pore sizes was more suitable for DETA. The hexagonal mesoporous structure was congenial to DETA and low PEI loading, while the cubic mesoporous structure was congenial to high PEI loading. The small pore size and the cubic mesoporous structure were proven to maintain the promotion effect of the adsorption temperature, while the hexagonal mesoporous structure could relieve the amine volatilization during the adsorption-desorption cycles. The cubic mesoporous structure could inhibit the generation of urea. By comparison, SBA-15 modified with 45 % had excellent performance, reaching a CO2 uptake of 160.55 mg/g and an amine efficiency of 0.360. This product could also control the total percentage of CO2 uptake lost after 30 cycles within 2.0 %, demonstrating the potential for practical application.
Functionalization of Hierarchically Porous Silica Monoliths with Polyethyleneimine (pei) for Co2 Adsorption

Xingzhong Guo,Li Ding,Kazuyoshi Kanamori,Kazuki Nakanishi,Hui Yang

DOI: https://doi.org/10.1016/j.micromeso.2017.02.076

IF: 5.876

2017-01-01

Microporous and Mesoporous Materials

Abstract:A novel CO2 sorbent was prepared by modifying polyethyleneimine (PEI) on hierarchically porous silica (HPS) monoliths with well-defined macro-mesopores through wet impregnation method. HPS monoliths before and after functionalization were characterized by scanning electron microscopy (SEM), differential thermal analysis/thermogravimetry (DTA/TG), fourier transform infrared spectroscopy (FT-IR) and nitrogen adsorption/desorption analysis (BET), and the CO2 adsorption-regeneration properties of as synthesized sorbents were investigated by thermogravimetric analysis (TG). The effects of loaded PEI amount as well as adsorption temperature and CO2 partial pressure on the CO2 adsorption performance of the as-prepared sorbents were also studied. The results showed that the porous structure of HPS-PEI sorbents was preserved after functionalization, while the specific surface area and pore volume decreased with increasing amount of amines to some extent. The use of PEI had a remarkable improvement on the CO2 adsorption capacity. With the increasing amount of PEI loaded, the CO2 adsorption capacity improved significantly. The highest CO2 adsorption capacity of 2.44 mmol (g sorbent)-1 was obtained at 75 degrees C in the CO2 partial pressure of 100 kPa for the HPS loaded with 60 wt% PEI. Adsorption/desorption cycles indicated that the PEI-modified HPS sorbents had a good stability and regeneration. (C) 2017 Elsevier Inc. All rights reserved.
CO2 Adsorption on Modified Mesoporous Silicas: The Role of the Adsorption Sites

Martin Ravutsov,Yavor Mitrev,Pavletta Shestakova,Hristina Lazarova,Svilen Simeonov,Margarita Popova

DOI: https://doi.org/10.3390/nano11112831

2021-10-25

Abstract:The post-synthesis procedure for cyclic amine (morpholine and 1-methylpiperazine) modified mesoporous MCM-48 and SBA-15 silicas was developed. The procedure for preparation of the modified mesoporous materials does not affect the structural characteristics of the initial mesoporous silicas strongly. The initial and modified materials were characterized by XRD, N2 physisorption, thermal analysis, and solid-state NMR. The CO2 adsorption of the obtained materials was tested under dynamic and equilibrium conditions. The NMR data revealed the formation of different CO2 adsorbed forms. The materials exhibited high CO2 absorption capacity lying above the benchmark value of 2 mmol/g and stretching out to the outstanding 4.4 mmol/g in the case of 1-methylpiperazin modified MCM-48. The materials are reusable, and their CO2 adsorption capacities are slightly lower in three adsorption/desorption cycles.
Grafting Poly(ethyleneimine) on the Pore Surface of Poly(glycidyl Methacrylate-Trimethylolpropane Triacrylate) for Preparation of the CO2 Sorbent

Lijuan Nie,Lu Bai,Jian Chen,Junsu Jin,Jianguo Mi

DOI: https://doi.org/10.1021/acs.energyfuels.9b03204

IF: 4.6541

2019-01-01

Energy & Fuels

Abstract:A meso/macroporous interconnected polymer sorbent was prepared for CO2 capture by means of suspension polymerization of water-in-oil emulsion in aqueous solution. In the emulsion, poly(ethyleneimine) was dissolved in the water phase and enveloped into the oil phase containing glycidyl methacrylate and trimethylolpropane triacrylate. After polymerization and dehydration, poly(ethyleneimine) chains were grafted onto the macroporous surface of poly(glycidyl methacrylate-trimethylolpropane triacrylate) via the reaction between amine and epoxy groups. Physicochemical characterizations were carried out to evaluate its comprehensive performance in the adsorption/desorption process. The sorbent has exhibited optimum porous structure, high CO2/N-2 selectivity, acceptable CO2 uptake, and enhanced anti-oxidation and anti urea capacities. Notably, the energy penalty for sorbent regeneration is 2.31 MJ.kg(-1)(CO2), lower than the consumptions in the systems of alcohol amine absorption or poly(ethyleneimine)-silica adsorption.
Polyethyleneimine-Nano Silica Composites: A Low-Cost And Promising Adsorbent For Co2 Capture

kaimin li,jianguo jiang,sicong tian,feng yan,xuejing chen

DOI: https://doi.org/10.1039/c4ta04275a

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:Adsorbents for CO2 captured with nano silica as support were synthesized by impregnating polyethyleneimine (PEI) into nano silica. For impregnation of PEI into nano silica, the 2-40 nm pore of silica support plays an important role in the synthesis process of adsorbents. The PEI loading content, adsorption temperature and CO2 partial pressure influenced CO2 adsorption capacity and PEI utilization efficiency. At 105 degrees C and under 1 atm CO2 partial pressure, the adsorbent with 60% PEI loading content obtained a CO2 adsorption capacity of 186 mg g(-1) adsorbent and a PEI utilization efficiency of 304 mg g(-1) PEI. The CO2 cycling adsorption-desorption was tested under the condition as follows: adsorption at 90 or 105 degrees C under pure CO(2)and desorption at 120 degrees C under pure N-2 showed relatively good adsorption-desorption stability, and no evident deactivation of amines was observed under this condition. However, for adsorption at 90 or 105 degrees C under pure CO2 and desorption at 135 or 150 degrees C under pure CO2, evident deactivation of amines occurred, and the formation of linear or cyclic urea is one reason which led to the decrease of CO2 adsorption capacity.
Amine-tethered Adsorbents Based on Three-Dimensional Macroporous Silica for CO(2) Capture from Simulated Flue Gas and Air.

Fa-Qian Liu,Lei Wang,Zhao-Ge Huang,Chao-Qin Li,Wei Li,Rong-Xun Li,Wei-Hua Li

DOI: https://doi.org/10.1021/am500089g

IF: 9.5

2014-01-01

ACS Applied Materials & Interfaces

Abstract:New covalently tethered CO2 adsorbents are synthesized through the in situ polymerization of N-carboxyanhydride (NCA) of l-alanine from amine-functionalized three-dimensional (3D) interconnected macroporous silica (MPS). The interconnected macropores provide low-resistant pathways for the diffusion of CO2 molecules, while the abundant mesopores ensure the high pore volume. The adsorbents exhibit high molecular weight (of up to 13058 Da), high amine loading (more than 10.98 mmol N g(-1)), fast CO2 capture kinetics (t1/2 < 1 min), high adsorption capacity (of up to 3.86 mmol CO2 g(-1) in simulated flue gas and 2.65 mmol CO2 g(-1) in simulated ambient air under 1 atm of dry CO2), as well as good stability over 120 adsorption-desorption cycles, which allows the overall CO2 capture process to be promising and sustainable.
Sponge-like polyethyleneimine adsorbents with interconnected open channels enabling ultra-high CO 2 adsorption and separation capacity

Haorui Liu,Xiaoqiong Wang,Shixun Chen,Shuixia Chen

DOI: https://doi.org/10.1016/j.seppur.2023.125528

IF: 8.6

2023-11-04

Separation and Purification Technology

Abstract:A novel solid amine adsorbent with interconnect open-cell porous structure was successfully synthesized by crosslinking polyethyleneimine (PEI) with ethylene glycol diglycidyl ether (EGDE) via high internal phase emulsion (HIPE) polymerization. The preparation conditions were optimized. The adsorption performance of the prepared adsorbent for CO 2 was evaluated by fixed bed dynamic adsorption experiment. The results indicated that the optimal adsorbent PEI70K-E-HIPE-8 exhibited a record high CO 2 adsorption capacity of 14.22 mmol/g, amine efficiency of 83% and ratio of breakthrough capacity to equilibrium capacity of 0.92 (abbreviated as Q b /Q e ratio). Both adsorption capacity and adsorption kinetics are much better than those of PEI70K-E-gel-8 prepared without using HIPE template. The adsorbent also showed good CO 2 /CH 4 separation performance, a CH 4 productivity of 54.84 mmol/g could be obtained while using PEI70K-E-HIPE-8 to separated it from a 20 mL CO 2 /CH 4 (20:80, v:v) mixed gas, remarkably higher than that of PEI70K-E-gel-8 (0.28 mmol/g). PEI70K-E-HIPE-8 could keep a stable adsorption and separation performance after at lease 15 adsorption-desorption cycles. The superior CO 2 adsorption capacity and adsorption kinetics make it a promising candidate in practical CO 2 adsorption and CO 2 /CH 4 separation application.

engineering, chemical

Adsorption of Co2 on A Micro-/Mesoporous Polyimine Modified with Tris(2-Aminoethyl)Amine

Polyethylenimine-Grafted Hkust-Type Mof/Poiyhipe Porous Composites (Pei@Pgd-H) As Highly Efficient Co(2 )Adsorbents

Synthesis and CO2 Capture Behavior of Porous Cross-Linked Polymers Containing Pendant Triazole Groups

Polyethyleneimine-Modified UiO-66-NH2(Zr) Metal–Organic Frameworks: Preparation and Enhanced CO2 Selective Adsorption

Ultramicroporous CO 2 adsorbents with tunable mesopores based on polyimines synthesized under off-stoichiometric conditions

High CO2 adsorption on amine-functionalized improved macro-/mesoporous multimodal pore silica

CO2 Adsorption by Polyamine-Based Protic Ionic Liquid-Functionalized Mesoporous Silica: Regenerability and Influence of Flue Gas Contaminants

Microporous Polymelamine Network for Highly Selective Co2 Adsorption

Investigation of adsorption/desorption performance by aminopropyltriethoxysilane grafted onto different mesoporous silica for post-combustion CO2 capture

Adsorption Capacity of Carbon Dioxide on Amine Modified Mesoporous Materials with Larger Pore Sizes

Adsorption Separation of CO2 from Flue Gas by Hyperbranched Solid-Amine

Polyethyleneimine-Modified Amorphous Silica for the Selective Adsorption of CO2/N2 at High Temperatures

Carbon Dioxide Adsorption on Amine-Impregnated Mesoporous SBA-15 Sorbents: Experimental and Kinetics Study

A stable solid amine adsorbent with interconnected open-cell structure for rapid CO2 adsorption and CO2/CH4 separation

The Influence of Pore Size and Pore Structure of Silica-Based Material on the Amine-Modified Adsorbent for CO2 Capture

Functionalization of Hierarchically Porous Silica Monoliths with Polyethyleneimine (pei) for Co2 Adsorption

CO2 Adsorption on Modified Mesoporous Silicas: The Role of the Adsorption Sites

Grafting Poly(ethyleneimine) on the Pore Surface of Poly(glycidyl Methacrylate-Trimethylolpropane Triacrylate) for Preparation of the CO2 Sorbent

Polyethyleneimine-Nano Silica Composites: A Low-Cost And Promising Adsorbent For Co2 Capture

Amine-tethered Adsorbents Based on Three-Dimensional Macroporous Silica for CO(2) Capture from Simulated Flue Gas and Air.

Sponge-like polyethyleneimine adsorbents with interconnected open channels enabling ultra-high CO 2 adsorption and separation capacity