Abstract:In-plane uniaxial tension of AZ31 magnesium alloy sheet with non-basal texture has been conducted in order to demonstrate the effects of loading direction on the microstructure evolution and mechanical properties at ambient temperature. Loading axes are chosen to be along five directions distributed between rolling direction (RD) and transverse direction (TD), allowing various activities in involved slip and twinning modes to take place. As for twinning modes, electron backscattered diffraction observations confirm that the contribution of \({{\{ 10\overline{1}1\} }}\) compression twinning is minimal to the plastic deformation of all deformed samples. By comparison, \({{\{ 10\overline{1}2\} }}\) extension twinning (ET) not only serves as an important carrier on sustaining and accommodating plastic strain but also contributes to the emergence of TD-component texture with the progression of plastic strain. In terms of slip modes, analysis on Schmid factor demonstrates that the increasing tilted angle between loading direction and RD of sheet is unfavorable to the activation of basal <a> slip, whereas it contributes to the activation of prismatic <a> slip. These observations consequently explain the increasing tendency of 0.2% proof yield stress. Moreover, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET collectively contribute to the concentration of two tilted basal poles toward normal direction. With increasing angle between loading direction and RD, the activations of basal <a> slip and \({{\{ 10\overline{1}2\} }}\) ET are gradually weakened. This leads to a weakening tendency about concentration of two tilted basal poles, a generally increasing tendency about Lankford value (r-value) and a generally decreasing tendency about strain-hardening exponent (n-value).

Influence of Pre-Hardening on Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet

Improved Ductility of Magnesium Alloy Sheets by Pre-Hardening and Annealing

Influence of Pre-Tension on Free-End Torsion Behavior and Mechanical Properties of an Extruded Magnesium Alloy.

Mechanical Properties and Anisotropy of AZ31 Alloy Sheet Processed by Flat Extrusion Container

Effect of initial orientation on the microstructure and mechanical properties of textured AZ31 Mg alloy during torsion and annealing

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Dependence of Microstructure Evolution and Mechanical Properties on Loading Direction for AZ31 Magnesium Alloy Sheet with Non-basal Texture During In-Plane Uniaxial Tension

Effect of Crystal Orientation on the Mechanical Properties and Strain Hardening Behavior of Magnesium Alloy Az31 During Uniaxial Compression

Microstructure Evolution of AZ31B Magnesium Alloy Sheets Deformed in Different Deformation Directions

Influence of an Asymmetric Shear Deformation on Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Effect of initial orientation on microstructure and mechanical properties of AZ31 Mg alloy sheets via accumulated extrusion bonding

Enhanced Stretch Formability of AZ31 Magnesium Alloy Sheet by Secondary Regulation of Initial Twin Orientation

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Mechanical Properties and Microstructure Evolution of AZ31 Magnesium Alloy Sheet Subjected to High Strain Rates Loading of Different Orientations

Development of Mechanical Properties in AZ31 Magnesium Alloy Processed by Cold Dynamic Extrusion

Dynamic recrystallization, twinning behaviors and mechanical response of pre-twinned AZ31 Mg alloy sheet along various strain paths at warm temperature

Enhancement of Mechanical Properties and Corrosion Resistance of Magnesium Alloy Sheet by Pre-Straining and Annealing

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Texture Weakening of AZ31 Magnesium Alloy Sheet Obtained by a Combination of Bidirectional Cyclic Bending at Low Temperature and Static Recrystallization

Effect of Processing Variables on Microstructure and Mechanical Properties of AZ31B Magnesium Alloy Sheet