Abstract:The solid/gas eutectic unidirectional solidification process is a new kind of technology fabricating the lotus-type porous structure. Besides having the properties of large specific surface area, excellent sound absorption, penetrating performance etc. of traditional porous materials, the particularity of the lotus-type porous structure makes it has extraordinary mechanical and thermal properties. There is a great potential for lotus-type porous aluminum in the field of lightweight engineering and heat dissipation of chip owing to its low density, outstanding corrosion resistance and high thermal conductivity. However, the fabrication of lotus-type porous aluminum has always been been more difficulty than other metals. Until porous aluminum with excellent pore structure was fabricated under very small solidification rates (0.008 similar to 0.015 mm/s) and high superheat degrees of melt (240 similar to 340 K), the proper processing parameters were recognized to be essential for the coupled growth of solid/gas phases for Al-H-2 system, especially the solidification rate. In this work, a three-dimensional time-dependent model describing the evolution of single pore was established based on the theoretical analysis of mass transfer, gas bubble nucleation, pore growth, interruption and detachment. The morphology of single pore under different solidification rates were simulated during the Gasar process by using the finite difference method for Al-H-2 system. The research reveals: coupled growth of solid/gas phases can be achieved under the solidification rates from 0.15 mm/s to 0.005 mm/s. The average pore diameter which ranges from 100 pm to 1100 pm increases with decreasing the solidification rate. The pore length also increases while the pore aspect ratio is nearly a constant about 40 with decreasing the solidification rate. The simulated average pore diameter is in good agreement with the experimental values when solidification rate equals to 0.015 mm/s, and then being slightly lower than the experimental ones with decreasing the solidification rate. The diffusion of hydrogen into the melt during the solidification process is regarded as the main reason of the discrepancy between simulated and experimental average pore diameters. The maximum value of the simulated solidification rates for coupled growth of solid/gas phases in Al-H-2 system first increases from less than 0.01 mm/s to 0.15 mm/s and then being a constant, while the minimum ones increase from about 0.0001 mm/s to 0.01 mm/s with improving the overheat degree of melt and hydrogen partial pressure. By comparing the relative parameters of Al-H-2 and Cu-H-2 systems, the solubility of hydrogen is regarded to be the main parameter which determines solidification rates of coupled growth of solid/gas phases for Al-H-2 system.

Investigation on the Formation of Microporosity in Aluminum Alloys

Modeling of microporosity evolution and fatigue life of aluminum alloy castings

Hydrogen microporosity evolution and dendrite growth during long solidification of Al-Cu-Li alloys: Modeling and experiment

Numerical simulation of microporosity evolution of aluminum alloy castings

A Mathematical Model for Simulating the Microporosity of Squeeze Casting of Aluminum Alloy

Study on Macro- and Micromodeling of the Solidification Process of Aluminum Shape Casting

Multiphase-field Modelling of Hydrogen Pore Evolution During Alloy Solidification

Preliminary Study on Simulation of Microporosity Evolution and Fatigue Life of Aluminum Alloy Casting

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Numerical simulation of microstructure and microporosity morphology in directional solidification of aluminum-copper alloys: Effect of copper content and withdrawal rate

Three-dimensional visualization and quantification of microporosity in aluminum castings by X-ray micro-computed tomography

Quantifying the effects of cooling rates and alloying additions on the microporosity formation in Al alloys

Research on prediction of microporosity in Ti-Al alloy investment casting

MODELING AND SIMULATION OF STRUCTURAL FORMATION OF POROUS ALUMINUM IN GASAR SOLIDIFICATION

Study on Numerical Simulation of Mold Filling and Solidification Processes under Pressure Conditions

Understanding the formation process of shrinkage pores with a 3D dendrite growth model: from casting to additive manufacturing

Predicting hydrogen microporosity in long solidification range ternary Al-Cu-Li alloys by coupling CALPHAD and cellular automata model

Effects of cooling rates on microporosity in DC casting Al-Li alloy

Experiment on Microporosity in Squeezing Casting Aluminum Alloy Parts

Multiphase and multiphysics modeling of dendrite growth and gas porosity evolution during solidification

Simulation of gas porosity formation and interaction with dendrite and eutectic structures during solidification of Al-Si alloys