Abstract:Improving the toughness of epoxy resins (EP) with diverse thermoplastic polymers through curing reaction induced phase separation (RIPS) has been widely studied, with the prerequisite of designing and tailoring the phase morphology evolution of the blend. Herein, two typical amine-type curing agents, 4,4′-diamino diphenylmethane (DDM) with precuring temperature at around 150 °C and diethylenetriamine (DETA) at 80 °C were utilized to regulate and control the phase structures of EP-poly(ε-caprolactone) (PCL) blends. The curing temperature above or below the melting temperature (Tm) of PCL resulted in different states of PCL. The effect of curing temperature on the miscibility between EP matrix and PCL phase, and the correlation between phase morphology evolution and thermomechanical behavior, mechanical properties were comprehensively investigated for the first time. Results revealed that when the curing temperature of EPDDM-PCL blends was higher than the Tm of PCL, curing took place without phase separation; while distinct phase separation took place when EPDETA-PCL was cured at a temperature below the Tm of PCL. When the curing temperature was high, the PCL was able to dissolve completely in the resin before crosslinking began, so that semi-interpenetrating networks were formed; and that when the curing temperature was low, the PCL was unable to dissolve, and therefore formed separate particles. Consequently, the EPDDM-PCL blends exhibited all-leading mechanical properties due to the entanglement and slippage between PCL chains and EP networks. The strength of EPDETA-PCL was reduced but the toughness was improved for island-shaped PCL particles bridging or pinning the cracks during failure. These results elucidated the effect of the phase morphologies formed at different curing temperature on mechanical properties, and provided significant insights regarding the toughening of thermosets.

Miscibility, Intramolecular Specific Interactions and Mechanical Properties of A Dgeba Based Epoxy Resin Toughened with A Sliding Graft Copolymer

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Nonisothermal Reaction, Thermal Stability and Dynamic Mechanical Properties of Epoxy System with Novel Nonlinear Multifunctional Polyamine Hardener

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

STUDY ON DGE-BHBTMBP/E-51/DDS CURED

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Epoxy Toughening Using Low Viscosity Liquid Diglycidyl Ether of Ethoxylated Bisphenol‐a

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Curing kinetics and shape-memory behavior of an intrinsically toughened epoxy resin system

Influence of the Degree of Grafting on the Morphology and Mechanical Properties of Blends of Poly(butylene Terephthalate) and Glycidyl Methacrylate Grafted Poly(ethylene‐co‐propylene) (EPR)

Miscibility, crystallization behavior and specific intermolecular interactions in thermosetting polymer blends of novolac epoxy resin and polyethylene glycol

Toughening of Epoxy Resin with Poly(Methyl Methacrylate) Grafted Silica Core-Shell Particles

Synchronously Improving Mechanical and Thermal Performances of Cured Epoxy Resins by Epoxidized Polyether Sulphones As Modifiers

Curing Behavior, Rheological, and Thermal Properties of DGEBA Modified with Synthesized BPA/PEG Hyperbranched Epoxy after Their Photo-Initiated Cationic Polymerization

A new strategy to improve the toughness of epoxy thermosets by introducing the thermoplastic epoxy

Efficient Toughening of DGEBA with a Bio-Based Protocatechuic Acid Derivative

Effect of Ethylene/butyl methacrylate/Glycidyl Methacrylate Terpolymer on toughness and biodegradation of poly (l-lactic acid)

Toughening Of Epoxy Resin Using Reactive Liquid (Ctbn) Rubber

Effects of curing temperature on the structure and properties of epoxy resin-poly(ε-caprolactam) blends