Abstract:Abstract Background This study aimed to evaluate the stress distributions in endocrown restorations as applied to endodontically treated teeth (ETT), according to the factors of “margin design” (four levels) and “restorative material” (six levels). Methods Four 3D-finite elements models were constructed for endocrown restored molars considering different margin designs. Model A was prepared with a flat butt joint margin and received an endocrown with a 2.0-mm occlusal thickness. Model B was prepared with a 20° bevel margin and received an endocrown with a 2.0-mm occlusal thickness. Model C was prepared with an axial reduction and 1-mm shoulder margin and received an endocrown with a 2.0-mm occlusal thickness. Model D was prepared with an anatomic margin and received an endocrown with a 2.0-mm occlusal thickness. The following endocrown materials were used: In-Ceram Zirconia (Zr), Vita Suprinity (VS), IPS Empress (IE), Grandio blocs (GR), VisCalor bulk (VS), and CopraPeek Light (CP). The Load application (600 N) was performed at the food bolus and tooth surface during the closing phase of the chewing cycle. The results for the endocrown and tooth remnants were determined according to the von Mises stress. The failure risk of the cement layer was also calculated based on the normal stress criterion. Results Model D (with an anatomic margin) showed the greatest stress concentrations, especially in the irregular and sharp angles of the restoration and tooth remnants. The stress concentrated on the dentin was significantly lower in Model B with a 20° bevel margin (20.86 MPa), i.e., 1.3 times lower than the other three margin designs (27.80 MPa). Restorative materials with higher elastic moduli present higher stress concentrations inside the endocrown and transmit less stress to the cement layer, resulting in lower bonding failure risks. In contrast, materials with an elastic modulus similar to that of dentin presented with a more homogeneous stress distribution on the whole structure. Conclusions An endocrown with a 20° bevel margin design could be a favorable preparation option for ETT. Composite resins (GR and VC) exhibit a more even stress distribution, and seem to be more promising materials for endocrown molars.

Influence of Various Materials on Biomechanical Behavior of Endocrown-Restored, Endodontically-Treated Mandibular First Molar: A 3D-Finite Element Analysis

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Influence of restorative material and cement on the stress distribution of endocrowns: 3D finite element analysis

Biomechanical Assessment of Restored Mandibular Molar by Endocrown in Comparison to a Glass Fiber Post-Retained Conventional Crown: 3D Finite Element Analysis

Influence of margin design and restorative material on the stress distribution of endocrowns: a 3D finite element analysis

Influence of remaining tooth structure and restorative material type on stress distribution in endodontically treated maxillary premolars: A finite element analysis

Influence of Different Base Materials and Thicknesses on the Fracture Resistance of Endocrown: A Three-Dimensional Finite Element Analysis

Effect of Remaining Pericervical Dentin on Biomechanical Behavior of Endocrown-Restored Molars with Different Materials: Three-dimensional Finite Element and Weibull Analyses.

Optimizing restorative procedure and material selection for pulpotomized primary molars: Mechanical characterization by 3D finite element analysis

Three-dimensional Finite Element Stress Analysis of First Mandibular Premolar Restored by Different Materials under Loading

Biomechanical properties of different endocrown designs on endodontically treated teeth

[Three-Dimensional Finite Element Initial Analysis on the Structure Defect Restoration of Mandibular First Molar under Static and Impact Loads].

Biomechanical Analysis of Repairing Large Area Defects of Mandibular First Molar with Endocrown and Post-core Crown

Influence of restorative materials on the mechanical properties of maxillary first molars with different degrees of cryptic fractures and defects: A finite element analysis

Evaluation of Biomechanical Stability of Teeth Tissue According to Crown Materials: A Three-Dimensional Finite Element Analysis

The three-dimension finite element analysis on mandibular first molar restored with different designed fiber post-core and all ceramic crown

[Finite Element Analysis of First Maxillary Molars Restored with Different Post and Core Materials].

Stress Analysis of First Permanent Mandibular Molar with Class 1 Restorations of Different Cement Bases by Occlusive Load: A Finite Element Analysis

Effect of Access Cavities and Canal Enlargement on Biomechanics of Endodontically Treated Teeth: A Finite Element Analysis

Comparison of the biomechanical effects of the post-core crown, endocrown and inlay crown after deep margin elevation and its clinical significance

Effect Of Central Retainer Shape And Abduction Angle During Preparation Of Teeth On Dentin And Cement Layer Stress Distributions In Endocrown-Restored Mandibular Molars