Abstract:AIM:To observe the influence of different level of distal occlusal teeth defect of the mandibular first molars after root canal therapy on the teeth resistance which were filled with amalgam or composite resin and restored with NiCr metal crown;and to compare if the two different filling materials had different effects.METHODS:3-dimensional finite element models of the minimum, middle and maximum distal occlusal structure defect without the pulp chamber wall involved and the maximum distal occlusal structure defect with the pulp chamber wall involved were built by the advanced 3-dimensional laser scanning and 3-dimensional computer assisted design technique. The Mohr strength theory was applied for comparing the maximum Mohr stress value of the dentin and stress concentration areas in four models under four different loads.RESULTS:Under the maximum, vertical and inclined loads,the maximum Mohr stress values of the dentin of the two kinds of restorations were obviously smaller than the stretch limit of the strength of the dentin.Under horizontal direct load,the maximum Mohr stress values of the dentin of the two kinds of restorations increased remarkably.The stress area in the model with amalgam filling and full crown restoration was generally larger than that in the model with composite resin filling and full crown restoration.The maximum Mohr stress value of the dentin of the model with composite resin filling and full crown restoration was greater than that of the model with the amalgam filling and full crown restoration.CONCLUSION:Under normal masticatory force,when the distal occlusal teeth defect of the mandibular first molars does not involve the pulp chamber wall and the thickness of buccal and lingual wall of the tooth preparation is at least 1 mm,and when the distal occlusal teeth defect involves the pulp chamber wall and the thickness of lingual wall is at least 1 mm and the thickness of buccal is at meast 2.5 mm,the restorations of composite resin,amalgam filling and full crown can be considered to be a proper restoration in clinic. Under the condition of bruxism,the measures of decreasing the bite force should be applied. For the case of bigger distal occlual teeth defect and the defect involving the pulp chamber wall,the composite resin filling and the full crown restoration are relatively better than amalgam filling and full crown restoration.

Three-dimensional Finite Element Stress Analysis of First Mandibular Premolar Restored by Different Materials under Loading

Three-dimensional Finite Element Method Stress Analysis of First Mandibular Premolar with Various Degree of Wedge-shaped Defects under Loading

[Two-Dimensional Finite Element Stress Analysis of Simulating Restored Teeth with Wedge-Shaped Defects under Loads].

Three-dimensional finite element analysis of severe wedge-shaped defective premolar restored with fiber post and composite resin

[Finite Element Analysis of First Maxillary Molars Restored with Different Post and Core Materials].

[Three-Dimensional Finite Element Analysis on Half of the Structure Defect with Post Core and All-Ceramic Crown Restoration of Mandibular First Molar].

The Stress Analysis on Filling and Full Crown Restoration of the Structure Defect of the First Mandibular Molar

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

THREE-DIMENSIONAL FINITE ELEMENT ANALYSIS OF THE CLASSⅠCAVITY RESTORED BY COMPOSITE RESIN

[Three-Dimensional Finite Element Initial Analysis on the Structure Defect Restoration of Mandibular First Molar under Static and Impact Loads].

A 3-Dimension Finite Element Mechanical Analysis on DO Defect Restoration of the Mandibular First Molar

Stress analysis on structure defect with different post core materials and full crown restoration of the permanent mandibular first molar

The three-dimension finite element analysis on mandibular first molar restored with different designed fiber post-core and all ceramic crown

Optimizing restorative procedure and material selection for pulpotomized primary molars: Mechanical characterization by 3D finite element analysis

Study on the fracture-resistant forces of premolars with wedge-shaped defects post restoration

Stress distribution of endodontically treated maxillary premolars restored with different cusp coverage design

[The Finite Element Analysis of Stress Distribution in Different Size of MO Cavities Restored with Composite Resin Inlays].

Three-dimensional finite element analysis of effect of root canal taper and post on tooth stress distribution]

[Three-Dimensional Finite Element Analysis of One-Piece Computer Aided Design and Computer Aided Manufacture Involved Zirconia Post and Core].

[Three Dimensional Finite Element Stress Analysis in the Vertical Fractured First Premolar after Bonding and Replantation].

Three-dimensional Finite Element Stress of the Medial-Occlusal (class Ⅱ)cavity Restored with Different Inlay