Abstract:Electrically-assisted forming has been proven to be an efficient process in terms of reducing forming flow stress, improving formability and supressing the springback for different hard-to-deform alloys. However, there is a controversial debate about whether the flow stress reduction with the introduction of electric current into a metallic specimen undergoing plastic deformation is attributed to Joule heat, additional athermal effect, namely the electroplasticity, or their combination thereof. There is a lack of thorough understanding of different mechanisms inducing the flow stress reduction and formability improvement, which would hinder the development and application of innovative electrically-assisted forming processes. Most prior works have examined only one or two materials with similar electroplastic behaviours, making it difficult to resolve this debate. In this study, three typical materials with diverse electroplastic behaviours, i.e. copper, SS304 and Ti6Al5V, were investigated and compared via electrically-assisted tensile tests and thermally-assisted tensile tests. The flow stress of the copper specimens in the electrically-assisted tensile test was lower than that in the thermally-assisted tensile test, which verifies the existence of electroplasticity. However, the flow stresses of the SS304 specimens in the electrically-assisted tensile test and thermally-assisted tensile test were similar at the same temperature, indicating that the athermal effect on the flow stress is not evident. For the Ti6Al4V specimens, the athermal stress reduction was not significant at lower current densities. However, the electrically-assisted and thermally-assisted tensile tests results began to differ when the current density exceeded 37.6 A/mm2. According to the further discussion on the microstructure evolution of different materials, the introduced current improves the dislocation motions and recovery and consequently reduces the flow stress in simple face-centered cubic structure materials such as copper. However, these effects can be suppressed by stronger effects such as the solution hardening in stainless steels. The current also affects the phase transition, which in turn influences the hardening behaviours of Ti6Al4V. By clarifying the cause of conflicting electroplastic effects, a uniform analytical method calculating the short- and long-range stresses that considers the correlation of electrical and thermal effects on dislocation motion, solution hardening and phase transformation was developed for electrically-assisted forming processes. The model was also experimentally verified.

Investigation on Transient Electrically-Assisted Stress Relaxation of Qp980 Advanced High Strength Steel

Achieving Stress Relief in Martensitic Stainless Steel Via High-Density Pulsed Electric Current Treatment

Experimental Research of Transformation Plasticity for Q460D Steel

Machine learning for extending capability of mechanical characterization to improve springback prediction of a quenching and partitioning steel

Effect of complicated deformation behaviors during cold stamping on springback prediction of DP980 steel

Time-dependent springback prediction with stress relaxation effect for non-isothermal hot stamping of titanium alloy sheets

OS0101 Effect of Electropulsing on Recovery of Strain in Stainless Steel

X-ray Determination of Compressive Residual Stresses in Spring Steel Generated by High-Speed Water Quenching

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

Modelling of Q&P Steel Heat Treatment Process Based on Finite Element Method

Research on stress relaxation behavior of TA15 titanium alloy

Investigation on the effect of friction and material behavior models on the springback simulation precision: application to automotive part B-Pillar and material TRIP800 steel

Altering the Residual Stress in High-Carbon Steel through Promoted Dislocation Movement and Accelerated Carbon Diffusion by Pulsed Electric Current

Springback Control in Complex Sheet-Metal Forming Based on Advanced High-Strength Steel

Investigation of springback during electromagnetic-assisted bending of aluminium alloy sheet

Experimental Study on the Static Strain Aging of Q345 Steel Using Complementary In-Situ Non-destructive Testing Techniques

Analysis of springback for multiple bending considering nonlinear unloading-reloading behavior, stress inheritance and Bauschinger effect

Electroplasticity in electrically-assisted forming: Process phenomena, performances and modelling

Application of distortional plasticity framework to EDDQ and TRIP steel sheets: Prediction of latent hardening and its influence on springback

A novel finite element simulation of hot stamping process of DP780 steel based on the Chaboche thermomechanically hardening model

Improving the high-cycle fatigue life of a high-strength spring steel for automobiles by suitable shot peening and heat treatment