Abstract:It has been long understood that fretting differs from sliding wear in that the relative displacement between the bodies is generally smaller than the size of the contact between them, with debris ejection from the contact thus playing an important role in the behaviour of the contact in fretting. Whilst these ideas were clearly articulated more than 30 years ago via Godet's third-body approach and Berthier's concept of the tribology circuit, calculation of wear rates in fretting have continued to employ Archard's wear equation (or approaches directly derived from it), despite this approach assuming that the rate of wear is controlled by the rate of generation of wear debris (as opposed to the rate of its ejection from the contact). It has been shown recently that when debris ejection is the rate-determining-process in fretting, the instantaneous rate of wear is inversely proportional to a characteristic dimension of the wear scar. When non-conforming specimen pair geometries (such as cylinder-on-flat) are employed in fretting testing, the wear scar size increases as wear proceeds, and thus the instantaneous rate of wear decreases. In this paper, wear equations have been derived for three commonly employed non-conforming pair specimen geometries, which all take the form <math>Vw=KRn−1Edn</math> (<math>Vw</math> is the wear scar volume, <math>R</math> is the radius of the non-plane specimen(s) in the pair and <math>Ed</math> is the frictional energy dissipated) where <math>n</math> varies between 0.67 and 0.8 depending upon the geometry and assumptions made regarding the governing equation. It is argued that the assumptions on which the analysis is based are most valid for the cylinder-on-flat contact configuration with fretting perpendicular to the cylinder axis where the length of the line contact is large compared to the wear scar width. It is demonstrated that, despite the often apparently good fit of experimental data to an Archard-type equation, it is not appropriate to employ such Archard-type approaches to the analysis of fretting data in situations where debris ejection is the rate-determining-process. The equations derived in this paper relating wear scar size to some measure of the duration of the test should be used for such analysis instead of the linear relationships generally employed in previous work.

Fretting Wear Volume and Wear Coefficient at the Dimple/gimbal Interface of a Hard Disk Drive Suspension

Microtribology of Hard Disk Drive for High Density Recording

Finite element analysis of fretting wear considering variable coefficient of friction

Modification methodology of fretting wear in involute spline

Effects of Surface Waviness and Dimple on Elastohydrodynamic Lubrication

Investigation of the Effect of Milli-Scale Dimples on Planar Contact Lubrication

Experimental Study of the Slider-Lube/Disk Contact State and Its Effect on Head-Disk Interface Stability

A flyability and durability dilemma in hard disk drives

Simulation of fretting wear in steel wires under variable coefficient of friction and variable wear coefficient

Contact size and debris ejection in fretting: The inappropriate use of Archard-type analysis of wear data and the development of alternative wear equations for commonly employed non-conforming specimen pair geometries

Nanoscale wear and kinetic friction between atomically smooth surfaces sliding at high speeds

Friction Characteristics of Floppy Disks

Friction-Wear and Noise Characteristics of Friction Disks with Circular Texture

Evolution of Bi-Gaussian Surface Parameters of Silicon-Carbide and Carbon-Graphite Discs in a Dry Sliding Wear Process

Experimental investigation and prediction method of fretting wear in rack-plane spline couplings

Research on the effect of fretting wear on the vibration characteristics of the tenon joint bladed disk

The Friction And Wear Behavior Of Laser Textured Surfaces In Non-Conformal Contact Under Starved Lubrication

Experimental and numerical study on the fretting wear-fatigue interaction evolution in press-fitted axles

Ti-6Al-4V fretting wear and a quantitative indicator for fretting regime evaluation

The Influence of Load and Angular Displacement Amplitude on the Torsional Fretting Wear of a Ball-on-Socket Cervical Disk Model

Calculation of gear tooth flank surface wear during an FZG micropitting test