Abstract:The modern compressor operation is challenged by the liquid presence in wet gas operating conditions. The liquid phase may affect the compressor stability by partially flooding the internal annular gas seals and inducing subsynchronous vibration (SSV). To improve the annular seal behavior and increase the rotor stability, high-precision results of leakage flow rates and rotordynamic force coefficients are needed for annular gas seals in wet gas conditions. In order to better understand the leakage and rotordynamic characteristics of the annular gas seal in wet gas conditions, a 3D transient CFD-based perturbation method was proposed for computations of leakage flow rates and rotordynamic force coefficients of annular gas seals with liquid phase in main gas phase, based on inhomogeneous Eulerian-Eulerian multiphase flow model, mesh deformation technique, and the multifrequency rotor whirling orbit model. Numerical results of frequency-dependent rotordynamic force coefficients and leakage flow rates were presented and compared for three types of noncontact annular gas seals, which include a smooth plain annular seal (SPAS), a labyrinth (LABY) seal, and a fully partitioned pocket damper seal (FPDS). These three seals were designed to have the identical rotor diameter, sealing clearance, and axial length. The accuracy and the availability of the present transient CFD numerical method were demonstrated with the experiment data of leakage flow rates and frequency-dependent rotordynamic force coefficients of the smooth plain seal with four inlet liquid volume fractions (LVFs) of 0%, 2%, 5%, and 8%. Steady and transient numerical simulations were conducted at inlet air pressure of 62.1 bar, pressure ratio of 0.5, rotational speed of 15,000 rpm, and inlet preswirl ratio of 0.3 for four inlet LVFs varying from 0% to 8% and 14 subsynchronous and synchronous whirling frequencies up to 280 Hz. The numerical results show that the inlet liquid phase has a significant influence on the leakage and rotordynamic coefficients for all three types of annular gas seals. The mixture leakage flow rate increases with the increasing inlet LVF, combining the decreasing gas-phase and linearly increasing liquid-phase leakage flow rates. The smooth plain seal leaks the most gas phase and liquid phase, followed by the pocket damper seal (PDS) and then the labyrinth seal. Increasing inlet LVF significantly decreases the direct stiffness and slightly increases the effective damping of the smooth plain seal. The labyrinth seal possesses evident negative direct stiffness and shows a noticeable decreasing effective damping with the increasing inlet LVF at the subsynchronous frequency range. Increasing inlet LVF obviously increases all the force coefficients of the pocket damper seal including the positive effective damping. From a rotordynamic viewpoint, the FPDS possesses a better liquid tolerant capability and so is a better sealing scheme for the balance piston seals and center seals of the centrifugal compressor in wet gas operating condition.

Dynamic Leakage Analysis of Noncontacting Finger Seals Based on Dynamic Model

Performance Analysis of the Cylinder Gas Film Seal between Dual-Rotor Reverse Shafts Considering Lubrication and Centrifugal Expansion Effects

Semi-Analytical Dynamic Analysis of Noncontacting Finger Seals

Investigation Into The Performance Of The Vl Seal Based On The 3d Model

Leakage, heat transfer and thermal deformation analysis method for contacting finger seals based on coupled porous media and real structure models

Numerical Investigation on the Leakage and Rotordynamic Characteristics for Three Types of Annular Gas Seals in Wet Gas Conditions

Numerical Calculation of Nonlinear Dynamic Characteristics for Labyrinth Seals

Numerical investigations on lifting and flow performance of finger seal with grooved pad

Leakage and Rotordynamic Performance of T Type Labyrinth Seal

Dynamic Performance Analysis of Gas Film Floating Ring Seals Based on the Reynolds–Bernoulli Small-Perturbation Model

Numerical Modeling of Dynamic Sealing Behaviors of Spiral Groove Gas Face Seals

Wear modelling and sealing performance prediction of C/C composite finger seal

Analysis of Leakage Flow and Dynamic Characteristics in Floating Ring Seals for High Pressure Turbopump

Determination of the Equivalent Rotordynamic Coefficients and Leakage of a T-Type Labyrinth Seal

Studies of Exit Pressure Recovery Coefficient and Its Effects on Dynamic Characteristics of Annular Water Seals

Analysis of mechanical characteristics and normal operating conditions of magnetic seals

Dynamic Response Analysis to Seal Chamber Pressure Perturbation of a New Double Spiral Groove Face Seal

Research on internal flow field analysis and power loss modeling of the expansion seal ring

Research On Fractal Heat Flow Characterization Of Finger Seal Considering The Heat Transfer Effect Of Contact Gaps On Rough Surfaces

Dynamic Performance of Liquid Smooth Annular Seal Operating in the Transition Regime

Thermoelastohydrodynamic Behavior of Gas Spiral Groove Face Seals Operating at High Pressure and Speed