Abstract:Cold-drawn pearlitic steel wires have the highest strength of all steel products. It is a promising way to enhance the mechanical properties by increasing the carbon content. However, the proeutectoid cementite forms easily due to the hypereutectoid composition and deteriorates the mechanical and processing properties of steel wires. It is important for hypereutectoid steel wire drawing to achieve a fine and fully pearlitic microstructure without proeutectoid cementite. The austenitization and following continuous cooling process were simulated in the dilatometer for a hypereutectoid steel. The microstructure was observed with OM and SEM. The transformation temperature, prior-austenite grain size, pearlitic interlamellar spacing and proeutectoid cementite thickness were determined by dilatometric curves or OM/SEM images. The austenite grain size increases rapidly with a higher temperature and almost keeps invariant with a longer austenitization time. Faster cooling rate, higher austenitization temperature or longer austenitization time decrease the starting and finishing temperature of phase transformation, widen the temperature range, refine the pearlitic interlamellar spacing and suppress the proeutectoid cementite precipitation (reduce the thickness or make it discontinuous). However, it is easy to form martensite which is bad for the homogeneity of pearlitic microstructure by increasing the cooling rate or austenitization temperature simply. A fine pearlite in a pseudoeutectoid microstructure is achieved by extending the austenitization time to 60 min and controlling the austenitization temperature and cooling rate. Discontinuous proeutectoid cementite is observed in the samples with the higher austenitization temperature. Higher austenitization temperature and longer time are helpful to weaken the carbon concentration gradient. The homogeneous carbon distribution restrains carbon diffusion for cementite nucleation during the proeutectoid cementite precipitation and pearlite transformation, which decreases the transformation temperature. Compare to pearlite transformation, the proeutectoid cementite precipitation is affected more strongly by the carbon diffusion due to a longer diffusion distance. Therefore, the precipitation amount of proeutectoid cementite is reduced if the carbon diffusion is restrained. The amount of grain corner and grain edge reduce more dramatically than that of grain boundary if austenite grain size increases. The proeutectoid cementite only nucleates in grain corner and grain edge. The pearlite nucleation can form in grain boundary. Therefore, the larger austenite grains result in the sharp reduction in the sites for nucleation of proeutectoid cementite. Then, the amount of proeutectoid cementite are reduced and the morphology becomes discontinuous.

Effects of high magnetic field on isothermal pearlite transformation and microstructure in a hypereutectoid steel

An integrated exploration from microstructure to mechanics in austenite to pearlite transformation of high carbon steel under high magnetic fields

Effects of high magnetic field on austenite formation and grain size in a hypereutectoid carbon steel

New Microstructural Features Occurring During Transformation from Austenite to Ferrite under the Kinetic Influence of Magnetic Field in A Medium Carbon Steel

Effect of a Magnetic Field on Phase Transformation of Steel

Inner connection of bainite and pearlite transformation in steels

Effects of Magnetic Field on Solid Phase Transformation

Effect of High Magnetic Field on Precipitation Behaviors and Mechanical Properties in Reduced Activation Steels

Analysis on the Crystallographic Orientation of Micro-Area under High Magnetic Field

Crystallographic orientation variation of isothermal pearlite under high magnetic field

Effect of Magnetic Field on Interfacial Energy and Precipitation Behavior of Carbides in Reduced Activation Steels

Effect of Magnetic Field on Solidification Structure of A Centrifugal Cast High Speed Steel Roll

EFFECTS OF AUSTENITIZATION AND COOLING RATESON THE MICROSTRUCTURE IN A HYPER-EUTECTOID STEEL

Effects of austenitization and cooling rates on the microstructure in a hypereutectoid steel

Effect of External Magnetic Field on the Microstructure and Properties of High-Speed Steel Roller by Centrifugal Casting

Investigation of Austenitization During Continuous Heating Process in Hypereutectoid Steels

Effect of alternating magnetic field on microstructure evolution and mechanical properties of M50 bearing steel during tempering process

Effect of High Magnetic Field Treatment on the Microstructure and Mechanical Property of Nial-Cr(Mo)-0.2hf Eutectic Alloy

The austenite to polygonal ferrite transformation in low-alloy steel: multi-phase-field simulation

Effect of Strain Rate History on the Piezomagnetic Field of Ferromagnetic Steels

Microstructure development in eutectic Al–Fe alloy during directional solidification under high magnetic fields at different growth velocities