Abstract:This paper investigates the influence of deposition conditions on the properties of yttrium oxide thin films. The paper focuses on the texture, optical and mechanical properties. With this objective, a series of yttrium oxide thin films with different thicknesses were deposited by direct current (DC) unbalanced reactive magnetron sputtering at high and low pumping speed. By changing the oxygen flow, depositions were performed in the three characteristic deposition modes for reactive magnetron sputtering, i.e., metallic, transition and poisoned mode. By using an oxygen flow directed to the substrate, full oxidation of the samples, as shown by X-ray photoelectron spectroscopy (XPS), in the three modes is obtained. Crystallographic characterization by X-ray diffraction (XRD) shows that films crystallize in the cubic phase with a strong (222) out-of-plane orientation at low oxygen flow. As the oxygen flow increases a mixture of cubic and monoclinic phase is obtained. In poisoned mode, the films consist of the cubic phase with preferred (420) orientation. Scanning electron microscopy (SEM) cross sections show, with increasing oxygen flow, a loss of the columnar structure. As the oxygen flow rates increase through the metallic, transition, and the poisoned mode, the grain size becomes gradually smaller. An overview diagram of all experimental results uncovers that the textural changes are closely linked to the oxygen partial pressure rather than the oxygen flow. The optical properties of films were investigated by spectroscopic ellipsometry (SE). The films with a columnar structure demonstrate superior hardness and modulus as well as the high plasticity.

Controllable Phase Formation and Physical Properties of Yttrium Oxide Films Governed by Substrate Heating and Bias Voltage

Formation and Rate Processes of Y2o3 Stabilized Zro2 Thin Films from Zr(Dpm)(4) and Y(Dpm)(3) by Cold-Wall Aerosol-Assisted Mocvd

Formation and Rate Processes of Y[sub 2]o[sub 3] Stabilized ZrO[sub 2] Thin Films from Zr(DPM)[sub 4] and Y(DPM)[sub 3] by Cold-Wall Aerosol-Assisted MOCVD

The Tunable Dielectric Properties of Sputtered Yttrium Oxide Films

Synthesis of YSZ film by solid single source PE-MOCVD method and characterization

Evolution of composition, microstructure and optical properties of yttrium oxide thin films with substrate temperature

Growth and characterization of yttrium oxide films by reactive magnetron sputtering

Study on Reactive Sputtering of Yttrium Oxide: Process and Thin Film Properties

Preparation of epitaxial yttria-stabilized zirconia with non-quilibrium t' phase and ferroelastic domain by pulsed laser deposition

TiO2 films prepared by DC reactive magnetron sputtering at room temperature: Phase control and photocatalytic properties

Yttrium Oxide Thin Films Prepared under Different Oxygen-Content Atmospheres: Microstructure and Optical Properties

Manipulation of phase transitions and electrical properties of Ba<sub>1-x</sub>Sr<sub>x</sub>TiO<sub>3</sub> thin films through orientation engineering

Independent Effects of Dopant, Oxygen Vacancy, and Specific Surface Area on Crystal Phase of HfO<sub>2</sub> Thin Films towards General Parameters to Engineer the Ferroelectricity

Epitaxial Growth and Metal-Insulator Transition of Vanadium Oxide Thin Films with Controllable Phases

Phase transition of PbTiO3 polycrystalline thin film prepared by metalorganic chemical vapor deposition on yttrium stabilized zirconium

Growth and characterization of Y2O3 thin films

Few-monolayer yttria-doped zirconia films: Segregation and phase stabilization

Controlled Growth of Complex Polar Oxide Films with Atomically Precise Molecular Beam Epitaxy

The characterization of ZrO2 films with different substrate bias voltages

Growth of Phase Pure Yttrium Iron Garnet Thin Films on Silicon: the Effect of Substrate and Post Deposition Annealing Temperatures

Growth and Physical Properties of Vanadium Oxide Thin Films with Controllable Phases