Abstract:Viscosity is an important parameter in reservoir development, especially in heavy oil production, processing, and transportation. Accurate measurement (+/- 5%) of heavy oil viscosities can be affected by sample handling, storage, and cleaning procedures. In addition, the type of viscometers and the corresponding experimental procedures can impact the accuracy of viscosity measurements. The objectives of this paper are to present the results of a systematic evaluation and comparison of different viscometers typically used in heavy oil viscosity measurements, provide references on the subject of viscometer selection, recommend developed measurement procedures for each viscometer, and generate a reliable viscosity database of dead and live heavy oils. The systematic study was performed using three viscometers typically used in heavy oil systems: a capillary viscometer (CV), an electromagnetic viscometer (EMV), and a rheometer (Rh). Viscosity measurements were performed over a range of temperature and pressure conditions varying from 293 to 422 K (from 20 to 149 degrees C) and from atmospheric pressure to 31.0 MPa (4500 psia). Three dead heavy oil samples ranging from 20 degrees to 11 degrees American Petroleum Institute (API) gravity and three live heavy oil samples prepared with gas/oil ratios (GORs) of 44.5, 30.3, and 17.8 Sm-3/Sm-3 by the three dead oils and methane gas were used. The study results showed that, within working limitations, each well-calibrated viscometer can reproduce reported values of viscosity standards with a relative error of less than 5%. The Rh with an open to atmospheric system provides the highest viscosity measurement scale but is limited to lower temperature tests to minimize light and/or intermediate component losses. The EMV and CV provide reasonably consistent viscosity values for both dead and live heavy oil samples as long as key conditions related to the experimental setup, measurement procedures, and sample preparation are met.

Viscosity Measurements of Hydrocarbon Fuel at Temperatures from (303.2 to 513.2) K and Pressures Up to 5.1 MPa Using a Two-Capillary Viscometer

Densities and Viscosities of Binary Mixtures of Cyclopropanecarboxylic Acid with Methanol, Ethanol, Propan-1-ol, and Butan-1-ol at Different Temperatures

Densities and Viscosities of Binary Mixtures of Methyl 4-Chlorobutyrate with Aromatic Hydrocarbons at T = (298.15 to 318.15) K

Viscosity Measurements of the H-2-CO2, H-2-CO2-CH4, and H-2-H2O Mixtures and the H-2-CO2-CH4-CO-H2O System at 280-924 K and 0.7-33.1 MPa with a Capillary Apparatus

Viscosity Measurements of the H2–CO2, H2–CO2–CH4, and H2–H2O Mixtures and the H2–CO2–CH4–CO–H2O System at 280–924 K and 0.7–33.1 …

A two-capillary viscometer for temperatures up to 473 K and pressures up to 100 MPa – operation and verification at low pressure

Two-capillary viscometer for temperatures and pressures relevant to CO 2 capture, transport, and storage – operation and improved analysis at high pressure

Measurements of the Viscosity of Hydrogen and a (Hydrogen + Methane) Mixture with a Two-Capillary Viscometer

Compressed Liquid Viscosity Measurements of Hfe-7000, Hfe-7100, Hfe-7200, and Hfe-7500 at Temperatures from (253 to 373) K and Pressures Up to 30 Mpa

Heavy Oil Viscosity Measurements: Best Practices and Guidelines

A New Method for Liquid Viscosity Measurements: Inclined-Tube Viscometry

Volumetric behaviour of (carbon dioxide + hydrocarbon) mixtures at high pressures

Viscosity Measurements of Nitrogen and Argon at Temperatures from 90 K to 200 K and Pressures Up To 5 MPa

Development of Viscosity Real-time Measurement System Based on Capillary Method

Simultaneous measurement of the density and viscosity for n-Decane + CO2 binary mixtures at temperature between (303.15 to 373.15) K and pressures up to 80 MPa

Measurements of Coefficient of Convective Heat Transfer for Endothermic Hydrocarbon Fuel Up to Supercritical Pressures

Development of a new PVT Measurement Method for the Hydrogen Mixture at High Temperatures and High Pressures

High-Pressure Viscosity Measurements for the Binary Mixture HFE-7500 + Diisopropyl Ether

Validation of an accurate vibrating-wire densimeter: Density and viscosity of liquids over wide ranges of temperature and pressure

Evaluation of Methods for Viscosity Simulations of Lubricants at Different Temperatures and Pressures: A Case Study on PAO-2

Utilization of a High-Pressure Vibrating Tube Densimeter for Liquids at Temperatures Down to 100 K