Abstract:In situ observation and measurement of high-temperature deformation of hot-section materials in scanning environments is helpful in understanding the microscopic failure and fracture mechanisms of these materials and estimating their safe life cycles. However, in situ high-temperature measurements in a scanning electron microscopy (SEM) environment pose major challenges in high-efficiency heat source design, establishment of stable high contrast microscopic images, and quantitative measurement of the deformation fields in the high-temperature environment. New methods and approaches must be therefore developed for quantitative measurement of these high-temperature mechanical properties. This article reports use of in situ SEM to measure the high-temperature deformation and fatigue properties of a nickel-based single crystal superalloy (NBSCS) up to 800 degrees C. A conductive heating source has been constructed based on numerical calculations of the thermal field inside the SEM chamber and analysis of the secondary electron spectrum and thermionic emissions received by the detector. Al2O3 nano-scale particles were coated on the NBSCS surfaces and were used to form speckle patterns to measure the deformation of NBSCS from room temperature up to 800 degrees C via a digital image correlation technique. The stable spatial geometric configuration and enhanced interfacial strength between the Al2O3 particles and the sample surface with increasing temperature validate the developed high-temperature speckle patterns. Tensile and fatigue experiments are performed for NBSCS samples using the developed system. Full-field displacements are obtained near the notch root and in situ fatigue crack propagation is reported in the temperature range from 600 degrees C to 800 degrees C.

In situ measurement of oxidation evolution at elevated temperature by nanoindentation

Effects of creep and oxidation on reduced modulus in high-temperature nanoindentation

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

In Situ Full-Field Measurement of Surface Oxidation on Ni-based Alloy Using High Temperature Scanning Probe Microscopy.

In situ determination of high-temperature oxidation evolution using micro-pillar array and scanning probe microscopy

Microstructure evolution of FeNiCr alloy induced by stress-oxidation coupling using high temperature nanoindentation

On the high-temperature oxidation behavior of a niobium-bearing high nickel-chromium alloy: microstructural evolution and implications on oxidation mechanisms

Mechanical Properties and Oxidation Characteristics of TiNiAl(Nb) Intermetallics

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

Nanomechanical Characterization of High-Velocity Oxygen-Fuel NiCoCrAlYCe Coating

In Situ AFM Observation of Mechanical Behavior of Beta Titanium Alloy in Nano-Indentation Test

An in Situ TEM Study of the Size Effect on the Thermally Induced Martensitic Transformation in Nanoscale NiTi Shape Memory Alloy

Investigation on nanoindentation and TOF-SIMS applications in the hydrogen and oxygen absorption behavior of Zr-Sn-Nb alloys

Measurement of Creep Stress Exponent of TC17 Titanium Alloy by Nanoindentation Method at Room Temperature

High-throughput nanoindentation mapping of cast IN718 nickel-based superalloys: influence of the Nb concentration

On Extracting Mechanical Properties from Nanoindentation at Temperatures up to 1000$^{\circ}$C

Room temperature nanoindentation creep of nitrocarburised AISI 4140 steel

Oxidation kinetics and high temperature in-situ observation of the oxidation behaviour of NbSi 2 at 1023 K

Temperature Effect on Nanotwinned Ni under Nanoindentation Using Molecular Dynamic Simulation

The Relationship Between the Morphology of the Scale and the Oxidation Kinetics at Elevated Temperatures in Ti–Al Alloys

In Situ Scanning Electron Microscopy-Based High-Temperature Deformation Measurement of Nickel-Based Single Crystal Superalloy Up to 800°C