Abstract:Thermoelectric (TE) energy conversion technology provides a promising way to improve the efficiency of fossil energy by generating electricity from low-grade waste heat. With regard to these applications, thermoelectric generators (TEGs) should be designed from system integration perspectives to simultaneously improve heat transfer efficiency and system simplification as well as the robust mechanical properties. However, typical TEGs fabricated by conventional methods barely accomplish such requirements. Herein, high-quality TEGs were assembled by combining the well-flowable spherical bismuth telluride (BT) powdered precursors and selective laser melting (SLM) technology. By optimizing the electronic and phonon transport properties through defect engineering driven by 3D printing, a high figure of merit was accomplished for 1.27 (p-type) and 1.13 (n-type) in BT. This achievement is primarily attributed to the nonequilibrium solidification mechanism, which leads to the formation of multiscale defects during the 3D printing process. The introduction of these multiscale defects enables the effective scattering of wide frequency phonons, leading to a substantial reduction in lattice thermal conductivity. Meanwhile, robust mechanical properties were obtained in the printed p-type/n-type BT TE materials parallel to the building direction (BD) with a compressive strength reaching 257/250 MPa by employing the fine grain structure and the high density of nanotwins introduced during the SLM process. A well shape-controllable and high-performance TEG was designed using 3D-printed BT half-rings, and an output power of 134 mW was achieved at a temperature gradient of 38.9 °C. Our study opens a new route for the great potential of TE materials based on standard commercial SLM 3D printing technology for low-grade waste heat emitted from structures with heterogeneous shapes.

3D Printing Fabrication of Amorphous Thermoelectric Materials with Ultralow Thermal Conductivity

3D Printing: 3D Printing Fabrication of Amorphous Thermoelectric Materials with Ultralow Thermal Conductivity (Small 44/2015)

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Ultrasonic-assisted Hot Pressing of Bi2Te3-based Thermoelectric Materials

High Thermoelectric Performance of a Sc2Si2Te6 Monolayer at Medium Temperatures: an Ab Initio Study.

Machine learning-assisted 3D printing of thermoelectric materials of ultrahigh performances at room temperature

3D Printing of Bi2Te3-Based Thermoelectric Materials with High Performance and Shape Controllability

Enhanced thermoelectric performance of 3D-printed Bi2Te3-based materials via adding Te/Se

3D-Printing of Shape-Controllable Thermoelectric Devices with Enhanced Output Performance

High performance thermoelectric composites via scalable and low-cost ink processing

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering

Fabrication and Property of High-Performance Ag-Pb-Sb-Te System Semiconducting Thermoelectric Materials

Ultra-fast fabrication of Bi2Te3 based thermoelectric materials by flash-sintering at room temperature combining with spark plasma sintering

2D hetero-nanosheets to enable ultralow thermal conductivity by all scale phonon scattering for highly thermoelectric performance

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting

Designing Cost-Performance Porous Thermoelectric Materials by Interface Engineering Through Atomic Layer Deposition

Making High Thermoelectric and Superior Mechanical Performance Nb0.88Hf0.12FeSb Half‐Heusler via Additive Manufacturing

Boosting thermoelectric performance of n-type Bi2Te2.7Se0.3 alloy by 3D printing induced in-situ texture engineering