Abstract:The well converged transporting valence bands in SnTe-MnTe alloys ensures a superior electronic performance, while their thermal transport properties still need to be further optimized for higher thermoelectric performance. Herein, the mechanical alloying is utilized to fabricate the SnTe-15%MnTe-2%Bi alloys, leading to a remarkable reduction of grain size as well as the formation of dense dislocations. Unexpectedly, the solubility of MnTe is reduced to ∼6% by mechanical alloying at room temperature, inducing an enhanced phonon scattering from nanoprecipitates. These full-scale hierarchical microstructures effectively decrease the lattice thermal conductivity of SnTe-15%MnTe-2%Bi to ∼0.5 W m−1 K−1 at 850 K. In addition, the increased vacancy formation energy triggers a reduction in carrier concentration (∼3 × 1019 cm−3) due to the decreased MnTe content in matrix. Moreover, the energy filtering effect through precipitate-matrix interface enables an improvement in Seebeck coefficient. Accordingly, the figure of merit of SnTe-15%MnTe-2%Bi is dramatically increased to ∼1.5 at 850 K by mechanical alloying. This work clearly demonstrates that mechanical alloying changes the composition and microstructure of materials, which significantly affect the thermoelectric transport properties, enabling an obvious performance enhancement.

Fine-grained Lead-Free P-Type AgSn 4 SbTe 6 Thermoelectric Materials Synthesized by Mechanical Alloying and Spark Plasma Sintering

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Composition Optimization of P-Type AgSn M SbTe M +2 Thermoelectric Materials Synthesized by Mechanical Alloying and Spark Plasma Sintering

Powder Metallurgic Synthesis of Mid-Temperature Lead-Free Agsn18sbte20 Thermoelectric Materials and Processing Influence on Thermoelectric Performance

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering

AgPbSbTe Thermoelectric Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering(SPS)

Fabrication and Property of High-Performance Ag-Pb-Sb-Te System Semiconducting Thermoelectric Materials

Preparation of AgxPbmSbTe2+m-Based Thermoelectric Materials by MA-SPS Method and Evaluation of Their Thermoelectric Properties

Lead-free AgSn4SbTe6 Nanocomposites with Enhanced Thermoelectric Properties by SiC Nanodispersion

Thermoelectric enhancement at low temperature in nonstoichiometric lead-telluride compounds

Approaching the Minimum Lattice Thermal Conductivity of P-Type SnTe Thermoelectric Materials by Sb and Mg Alloying.

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Fast fabrication of SnTe via a non-equilibrium method and enhanced thermoelectric properties by medium-entropy engineering

Thermoelectric Performance of AgPb X SbTe 20 ( X = 17 to 23) Bulk Materials Derived from Large-Particle Raw Materials

Band convergence and nanostructure modulations lead to high thermoelectric performance in SnPb0.04Te-y% AgSbTe2

Research Progress on Processing of Thermoelectric Materials by Mechanical Alloying Combined with Spark Plasma Sintering

Mechanical alloying boosted SnTe thermoelectrics

Low Thermal Conductivity and Improved Figure of Merit in Fine-Grained Binary PbTe Thermoelectric Alloys

Thermoelectric Properties of Sn-S Bulk Materials Prepared by Mechanical Alloying and Spark Plasma Sintering

Enhanced thermoelectric properties of p-type SnS0.2Se0.8 solid solution doped with Ag

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting