Abstract:INTRODUCTION: The purpose of this study was to evaluate the influence of a contracted endodontic cavity (CEC) on dentin preservation, biomechanical property, and instrumentation efficacy of first permanent molars in comparison with a traditional endodontic cavity (TEC).METHODS: Forty-eight extracted intact maxillary and mandibular first molars were selected and scanned by micro-computed tomographic (micro-CT) imaging. Each tooth type was anatomically matched and assigned to the CEC group or the TEC group (n = 12). After root canal instrumentation with the ProGlider (Dentsply Maillefer, Ballaigues, Switzerland) and WaveOne Gold (Dentsply Maillefer), the specimens were scanned by micro-CT again. Pre- and postpreparation micro-CT imaging was used to evaluate the dentin preservation and instrumentation efficacy. The results on volume and thickness reduction in the coronal dentin and pericervical dentin (PCD), root canal volume and surface area, percentage of unprepared surface area, canal transportation and centering ratio, and canal wall thickness in the "danger zone" were measured and analyzed with the Shapiro-Wilk and independent sample t tests. Based on micro-CT imaging of maxillary and mandibular first molars, CEC and TEC models were constructed on the intact tooth, and 2 different static loads were applied to the occlusal load points. The stress distribution patterns and von Mises stress on the occlusal surface and cervical region were assessed by 3-dimensional finite element analysis.RESULTS: The CEC had a significantly lower volume and thickness reduction of coronal dentin and PCD above the alveolar crest compared with the TEC group (P < .05), whereas no difference was observed in PCD below the alveolar crest between the 2 groups (P > .05). There was no difference regarding all instrumentation efficacy outcomes (root canal volume and surface area, percentage of unprepared surface area, canal transportation and centering ratio, and canal wall thickness) in the danger zone between the 2 groups (P > .05). The CEC effectively reduced the maximum von Mises stress and stress concentration area on the occlusal surface and cervical region compared with the TEC.CONCLUSIONS: The CEC preserved more coronal dentin and PCD above the alveolar crest and thus reduced stress concentration on the occlusal surface and cervical region. The CEC had no significant adverse effects on the instrumentation efficacy compared with the TEC given that the instrumentation procedures were performed with ProGlider and WaveOne Gold files.

[The Effect of Coronal Preflaring on the Working Length Measurement of Root Canals in Molars].

The effect of preflaring in the human first molars on the root canal curvature and the initial apical file size determination

Empirical formulas for design and optimization of 1.5 mu m InGaAs/InGaAsP strained-quantum-well lasers

The Impact of Coronal Flaring Files on Pericervical Dentin Thickness in Mandibular Molars

[Impact of Apical Preparation Diameter on Fracture Resistance of Mandibular Premolar Roots].

Fracture Resistance of Roots in Mandibular Premolars Following Root Canal Instrumentation of Different Sizes.

Coronal root canal morphology of permanent two-rooted mandibular first molars with novel 3D measurements

Three-dimensional analysis of coronal root canal morphology of 136 permanent mandibular first molars by micro-computed tomography

Root canal curvature as a prognostic factor influencing the diagnostic accuracy of radiographic working length determination and postoperative canal axis modification: an in vitro comparative study

Nuclear magnetic resonance analysis of acute and chronic myocardial infarction in dogs: alterations in spin-lattice relaxation times.

COMPARATIVE ANALYSIS OF APICAL EXTRUSION OF DEBRIS AND SHAPING ABILITY IN CURVED ROOT CANALS USING FOUR DIFFERENT NITI INSTRUMENTS

Occurrence and solution to overcome 1st RESET resistance pinning effect in Ti/HfOx based RRAM for low power nonvolatile memory applications

In-depth morphological evaluation of tooth anatomic lengths with root canal configurations using cone beam computed tomography in North American population

Comparison of Two Post Preparation Methods in Mandibular Second Molars with a C-shaped Root Canal Configuration.

Effect of Access Cavities and Canal Enlargement on Biomechanics of Endodontically Treated Teeth: A Finite Element Analysis

Assessment of the coronal root canal morphology of permanent maxillary first molars using digital 3D-reconstruction technology based on micro-computed tomography data

Pericervical Dentin Metrics in Mandibular First Molars Determined With Digital Periapical Radiography and Cone-beam Computed Tomography

Effect of Access Cavity Preparation on Dentin Preservation, Biomechanical Property, and Instrumentation Efficacy: A Micro–Computed Tomographic Study

Comparison of the incidences of apical root cracks after canal preparation with two nickel-titanium rotary systems:an in vitro study

Assessment of Biomechanical Preparation Influence on Various Root Canal Curvatures

Influence of access cavity design on root canal instrumentation efficacy in molars - An in vitro study